Westerbeke preheat with torch? - SailNet Community

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Engines > Diesel
 Not a Member? 
  #1  
Old 2 Weeks Ago
Junior Member
 
Join Date: Aug 2012
Location: Richmond, VA & Mathews
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
Westerly Pippin is on a distinguished road
Westerbeke preheat with torch?

Has anyone started their diesel engines with a torch as a preheater from the air intake? I have a Westerbeke 4107 - going on one year new to me. It is cold natured during the winter. A mechanic in a very reputable yard, the boat is no longer there, helped me start it in March last year with a heat gun. I have a glow plug in the top of the intake, which may need replaced, but haven't done that yet...I know it works, just not how well. I would like to know if a torch will serve the same purpose, safely, as the heat gun, for future use. Power for the heat gun isn't always available.
thanks
Reply With Quote Quick reply to this message Share with Facebook
  #2  
Old 2 Weeks Ago
capta's Avatar
Master Mariner
 
Join Date: Jun 2011
Location: somewhere in the Windward or Leeward Islands
Posts: 1,745
Thanks: 17
Thanked 90 Times in 85 Posts
Rep Power: 4
capta is on a distinguished road
Re: Westerbeke preheat with torch?

Diesel is generally considered to be a safe fuel, but I do think a propane torch would be pushing things a bit. Start the engine as it was designed to with the glow plug unless you have your boat very well insured.
__________________
"Any idiot can make a boat go; it takes a sailor to stop one." Spike Africa aboard the schooner Wanderer in Sausalito, Ca. 1964.
Reply With Quote Quick reply to this message Share with Facebook
  #3  
Old 2 Weeks Ago
BarryL's Avatar
Senior Member
 
Join Date: Aug 2003
Location: Long Island, NY
Posts: 1,673
Thanks: 3
Thanked 32 Times in 29 Posts
Rep Power: 12
BarryL is on a distinguished road
Re: Westerbeke preheat with torch?

Hey,

What happens if you try to start the engine 'as is'? Do you use the glow plugs at all? Does the engine eventually start? What temps are you trying to start the engine at?

My last boat had a Universal Diesel with about 4000 hours on it. It ran great but did not like to start when the temps were below 50. It had glow plugs, and I rewired them, and that helped, but the engine was hard to start below 50. I would have to crank it for over 10 seconds (when it was 70 out it would start in 2-3 seconds). If the batteries were low it would not want to start at all.

For me, the solution was starting fluid (ether). I know most people would not recommend it, but for me it worked great. Spray a 1 second shot into the intake, wait a minute, then the engine would start in 2-3 second when the exterior temp was 30. Since I'm mostly a fair weather sailor, I only used ether 3-4 times a year. I did that for 5-6 years without any problems.

Good luck,
Barry
__________________
Barry Lenoble
Deep Blue C, 2002 C&C 110
Mt. Sinai, NY

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Reply With Quote Quick reply to this message Share with Facebook
  #4  
Old 2 Weeks Ago
T37Chef's Avatar
Senior Member
 
Join Date: Oct 2006
Posts: 4,364
Thanks: 74
Thanked 40 Times in 35 Posts
Rep Power: 9
T37Chef will become famous soon enough
Re: Westerbeke preheat with torch?

I resorted to ether a few times on my old Westerbeake 50 when it was cold...it just made awful sounds. As I understand it, its pretty common for large diesel trucks to have ether injection on them for cold starts but I just think thats a last resort knowing it could do serious damage to the engine?

A reputable mechanic suggested I pull the fuel and crank the engine for 5-10 seconds and not dump cold fuel into the cylinder. ..then push the fuel stop in and crank it like normal. This worked very well for me, no awful noise and actually put less wear on the starter and batteries.

I'm not mechanic but plan B made better sense to me.

I have also heard using WD 40 or propane (unlite) but never a lit torch?

These days, even in the cold my new Beta starts like a gas engine and havent used the glow plugs yet, how sweet it is
__________________
Cheers,
Shawn & the crew of S/V Windgeist

1982 Tartan 37 CB - Hull #358


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Reply With Quote Quick reply to this message Share with Facebook
  #5  
Old 2 Weeks Ago
TQA's Avatar
TQA TQA is offline
Bombay Explorer 44
 
Join Date: Apr 2009
Posts: 2,707
Thanks: 0
Thanked 59 Times in 55 Posts
Rep Power: 6
TQA is on a distinguished road
Re: Westerbeke preheat with torch?

What you call a heater may well be a CAV Thermostart. This drips diesel onto a heating element. When you crank the diesel ignites and the flames are drawn into the cylinders. This is an excellent cold start device and is still available.

http://www.ebay.co.uk/itm/Thermostar...-/121218138141

Boring story. I was on a recovery in the middle of nowhere trying to pull a tracked vehicle out of a tidal channel. It had been submerged for 3 hours. We changed the oil and supplied fresh diesel plus a new battery but it would not start. [ It was brass monkey weather ] An Irish laborer showed us how to crumple up newspaper stuff it into the inlet manifold, pour on a little diesel and ignite the paper. We cranked and she fired up straight away. Exhaust was interesting for a few seconds.

But in answer to the OPs question, yes any heat source fed into the inlet manifold will help. I have used hair dryer, heat gun, butane torch etc over the years. If using a butane torch remove the air filter element. [ This is important! ]

Last edited by TQA; 2 Weeks Ago at 11:03 AM.
Reply With Quote Quick reply to this message Share with Facebook
  #6  
Old 2 Weeks Ago
Junior Member
 
Join Date: Aug 2012
Location: Richmond, VA & Mathews
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
Westerly Pippin is on a distinguished road
Re: Westerbeke preheat with torch?

Thank you for all the responses. I'll try to clarify a few issues. The glow plug is on the air intake and supposed to create a small flame that is then sucked into the air intake. I don't think it is a CAV heater, from memory it looked more like a glow plug in size, but I'll check soon. And I'm not sure if it actually ignites, this is on my long list of to do's and probably replace. I've only used the heat gun a few times and it works well with the air intake bell removed, but I don't think I can run it with my current setup off the batteries/converter. I was interested in other heating approaches only for situations when away from a dock as a last resort. Also this Westerbeke 4107 doesn't have block glow plugs. When the temp is below 50, approximately, it does become more difficult to start without heat. Thanks again for the help.
Reply With Quote Quick reply to this message Share with Facebook
  #7  
Old 2 Weeks Ago
svHyLyte's Avatar
Old as Dirt!
 
Join Date: Nov 2008
Location: Tampa Bay Area
Posts: 2,835
Thanks: 15
Thanked 116 Times in 110 Posts
Rep Power: 7
svHyLyte is on a distinguished road
Re: Westerbeke preheat with torch?

Quote:
Originally Posted by Westerly Pippin View Post
Has anyone started their diesel engines with a torch as a preheater from the air intake? I have a Westerbeke 4107 - going on one year new to me. It is cold natured during the winter. A mechanic in a very reputable yard, the boat is no longer there, helped me start it in March last year with a heat gun. I have a glow plug in the top of the intake, which may need replaced, but haven't done that yet...I know it works, just not how well. I would like to know if a torch will serve the same purpose, safely, as the heat gun, for future use. Power for the heat gun isn't always available.
thanks
The use of a high temperature open flame device in an engine space would be the height of folly in my view. (I can just imagine how you'd try to explain that to an insurance adjuster inspecting the ashes of your yacht.)

FWIW, the built in pre-heater or "flame start" system for 4-107/108 engines works quite well when necessary in very cold weather. Given your listed locale, however, it would seem to rarely be needed, however. That aside, use of the pre-heater requires that one hold the starting key in the "heat position" for 30-45 seconds or more until a trickle of fuel is ignited in the enclosed throat of the air intake. (When the fuel ignites, one can sometimes hear a "womp" sound.) With that, the engine will start up quite easily, typically within only a few revolutions.
__________________
"It is not so much for its beauty that the sea makes a claim upon men's hearts, as for that subtle something, that quality of air, that emanation from the waves, that so wonderfully renews a weary spirit."
Reply With Quote Quick reply to this message Share with Facebook
  #8  
Old 2 Weeks Ago
TQA's Avatar
TQA TQA is offline
Bombay Explorer 44
 
Join Date: Apr 2009
Posts: 2,707
Thanks: 0
Thanked 59 Times in 55 Posts
Rep Power: 6
TQA is on a distinguished road
Re: Westerbeke preheat with torch?

The link I gave includes a pic. There should be a small tank expresso cup size that gravity feeds the unit.

Energize the heater unit for 10 to 15 seconds before cranking.

The diesel does not 'catch' till you start cranking.
Reply With Quote Quick reply to this message Share with Facebook
  #9  
Old 2 Weeks Ago
deltaten's Avatar
Senior Member
 
Join Date: Oct 2012
Location: Lancaster Co. PA/ North East, MD
Posts: 761
Thanks: 7
Thanked 18 Times in 18 Posts
Rep Power: 3
deltaten is on a distinguished road
Send a message via Yahoo to deltaten
Re: Westerbeke preheat with torch?

Mebbe we're more squeemish/less adventurous nowadays?

I seem to recall reading somewher about back in the day there was a diesel that had a sheet metal tray that one would build a(n actual!) fire upon to pre-heat!
Not that I'd do that ; but I *have* been tempted on occasion

My Beta starts with some irregularity most times;particularly when less than 60 or so degrees. I tend to watch these types of threads carefully.

Carry On
__________________
S/V Chrysalis
'80 Watkins 27
North East, MD
Reply With Quote Quick reply to this message Share with Facebook
  #10  
Old 2 Weeks Ago
hellosailor's Avatar
Senior Member
 
Join Date: Apr 2006
Posts: 10,900
Thanks: 2
Thanked 103 Times in 100 Posts
Rep Power: 10
hellosailor has a spectacular aura about hellosailor has a spectacular aura about
Re: Westerbeke preheat with torch?

The reason WD40 (mainly kerosene) and unlit propane work, is because they tend to explode when compressed more easily than diesel does. Which in turn is why spray cans of "starting ether" are sold for that purpose, the ether explodes very readily.

Testing or replacing a glow plug shouldn't be a hard job though.
Reply With Quote Quick reply to this message Share with Facebook
Reply

Quick Reply
Message:
Options

By choosing to post the reply above you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Bernzomatic Handy Torch, Solder, Rope Cutter Tool PeterJYC Gear & Maintenance 9 12-28-2013 01:07 AM
Sailing champion starts Torch relay NewsReader News Feeds 0 05-19-2012 09:10 AM


All times are GMT -4. The time now is 10:40 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.