need help from the HAMS - SailNet Community
 
LinkBack Thread Tools
post #1 of 5 Old 03-04-2014 Thread Starter
Schooner Captain
 
UnionPacific's Avatar
 
Join Date: Dec 2013
Posts: 1,978
Thanks: 15
Thanked 20 Times in 20 Posts
Rep Power: 2
 
need help from the HAMS

I need a 470 microhenry 1/2 watt inductor
I translate the bands to be 460UF 10%
how would i order this?
This does not seem right....
4.7 UH INDUCTOR | AllElectronics.com
It looks completely different.
A point in the right direction is all i need. Thank you


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Last edited by UnionPacific; 03-04-2014 at 02:24 PM.
UnionPacific is offline  
Quote Quick Reply Share with Facebook
Sponsored Links
Advertisement
 
post #2 of 5 Old 03-04-2014
Mermaid Hunter
 
SVAuspicious's Avatar
 
Join Date: Oct 2006
Location: on the boat - Chesapeake
Posts: 3,984
Thanks: 0
Thanked 158 Times in 141 Posts
Rep Power: 9
 
Re: need help from the HAMS

Form factors aren't a big deal as long as the part fits.

You might also try Digikey and Neward Electronics.

sail fast and eat well, dave
S/V Auspicious
AuspiciousWorks.com
beware "cut and paste" sailors.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
SVAuspicious is offline  
Quote Quick Reply Share with Facebook
post #3 of 5 Old 03-04-2014
Senior Member
 
OPossumTX's Avatar
 
Join Date: Jul 2011
Location: Alvin, Texas
Posts: 181
Thanks: 30
Thanked 5 Times in 5 Posts
Rep Power: 5
 
Re: need help from the HAMS

WWW.Mouser.com
www.digikey.com
www.newark.com

Any of these suppliers will more than likely have what you want.

The original part may have axial leads (out the ends) or even be surface mount (no leads)

The form factor, wattage and voltage range will more than likely be key issues. Without more information on what this part is to be used for, that is as far as I can go.

Last edited by OPossumTX; 03-04-2014 at 04:05 PM.
OPossumTX is offline  
Quote Quick Reply Share with Facebook
post #4 of 5 Old 03-04-2014
Reward for lost Kraken!
 
hellosailor's Avatar
 
Join Date: Apr 2006
Posts: 11,496
Thanks: 5
Thanked 133 Times in 130 Posts
Rep Power: 11
   
Re: need help from the HAMS

"I translate the bands to be 460UF 10%"
That's microFarad, a capacitor. Not microHenry, an inductor.

Digikey's phone support will walk you through their inventory and set you up with the right part. I expect Newark and Mouser will as well, all three are great at sourcing parts. Offhand...either you meet the minimum order amount or you pay a stiffer shipping fee, so look around and see if you can use anything else, batteries, LEDs, buzzers, anything at all because sometimes it is simpler and cheaper to meet the minimum than not.

Of course, Real Men wind their own inductors, you just need some magnet wire and a core to wind it around. (VBG)
hellosailor is offline  
Quote Quick Reply Share with Facebook
post #5 of 5 Old 03-04-2014 Thread Starter
Schooner Captain
 
UnionPacific's Avatar
 
Join Date: Dec 2013
Posts: 1,978
Thanks: 15
Thanked 20 Times in 20 Posts
Rep Power: 2
 
Re: need help from the HAMS

seeing as how this is my first foray into any type of microelectronic repair, I doubt i will wind my own. I am barely on the verge of learning. All i know is i have a wonky SEA 222 unit, and this is what i need to fix it X2 and also some easier 22 microfarad 25 volt tantalum capacitors.

However the first part i need is a 470 microhenry 1/2 watt inductor.
I need two of each. I my just call. I also have learned i need axial termination.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
UnionPacific is offline  
Quote Quick Reply Share with Facebook
Reply

Quick Reply
Message:
Options

By choosing to post the reply above you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Register Now



In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.


User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Similar Threads
Thread Thread Starter Forum Replies Last Post
calling all hams: SiTex receiver question chrislab Gear & Maintenance 1 03-03-2004 05:37 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome