Glassing inside of centerboard trunk. - SailNet Community

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance
 Not a Member? 
  #1  
Old 05-05-2006
Junior Member
 
Join Date: Mar 2006
Posts: 27
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
Jack Tar is on a distinguished road
Glassing inside of centerboard trunk.

Any tips?
I tore the glass inside the trunk while driving out a heavily rusted centerboard. The trunk opening is about 3/4 of an inch. Do they make rollers that small? I'm sure someone has had to do this before. Any help is appreciated. Brian
Reply With Quote Share with Facebook
  #2  
Old 05-05-2006
sailandoar's Avatar
Senior Member
 
Join Date: Mar 2006
Location: Cape Fear, NC, USA
Posts: 208
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 9
sailandoar is on a distinguished road
Brush and plastic bondo squeege

Can't get into a 3/4" slot very far with anything. I would expect that the case was fabricated and set in place with a bedding putty and glassed to the hull/bilge securely on the outside of the case.

The glass you peeled up could just be a sort of pretty it up laminate rather than a structural water proofing one.

Whats it look like?
Reply With Quote Share with Facebook
  #3  
Old 05-07-2006
Junior Member
 
Join Date: Mar 2006
Posts: 27
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
Jack Tar is on a distinguished road
The trunk is made of 3/4" plywood glassed on both sides. The part I ripped is below the water line so leakage into the boat is not an issue. This is an open cat boat from the early sixties. It is a trailered boat so the plywood will dry out between uses. I am more concerned about long term damage. I sand blasted the center board and painted it and I'm ready to put it back in. I REALLY want to get out on the water so I may just forget about the torn glass and go sailing.
Reply With Quote Share with Facebook
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Morgan 22 Centerboard + Swing Keel Restoration briceburg Gear & Maintenance 5 06-16-2014 11:21 AM
Ericson25 Centerboard brbsim Gear & Maintenance 7 09-22-2006 11:16 PM
Securing centerboard when trucking a vessel roger_mexico General Discussion (sailing related) 2 10-20-2005 06:35 AM
islands 17 Anita Learning to Sail 1 07-11-2004 06:04 PM
water inside centerboard HGSmith Gear & Maintenance 2 04-27-2001 05:19 PM


All times are GMT -4. The time now is 08:24 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.