Tayana 37 Hawsepipe remove/replace - SailNet Community

   Search Sailnet:

 forums  store  

Quick Menu
Boat Reviews  
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Hatches and Portlights
Interior And Galley
Marine Electronics
Other Items
Plumbing and Pumps
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here

Go Back   SailNet Community > On Board > Gear & Maintenance
 Not a Member? 
Old 07-29-2001
Junior Member
Join Date: Jul 2001
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
John A. Oliver is on a distinguished road
Tayana 37 Hawsepipe remove/replace

Need to remove and replace, hopefully with same part, the fwd port hawse pipe. Just in case name is prob; the hawse is used to run mooring lines from cleat to dock through rail, six on boat, fwd midships and aft P & S. Need to know how to remove without destroying it. Any handy hints on reinstalling plus any special tools required, etc., much appreciated. Boat is in Mexico on the hard waiting for my return in October. Going back by bus so limited ability to haul too much stuff.
Reply With Quote Share with Facebook
Old 07-29-2001
RichH's Avatar
Senior Member
Join Date: Jul 2000
Location: Pennsylvania
Posts: 2,838
Thanks: 9
Thanked 75 Times in 68 Posts
Rep Power: 15
RichH will become famous soon enough
Tayana 37 Hawsepipe remove/replace

Join the Tayana owner''s email group here on Sailnet. Lots of Tayana owners have removed and rebedded their pipes.
Mine is through bolted with four bronze cap screws which were run-in then filed/formed flush with the flange. On mine I know I will have to drill out the remaining heads, etc. of the through bolts and replace with new bolts, etc. .... but then EVERY Tayana is ''different''. Join the group!
Reply With Quote Share with Facebook
Old 08-20-2001
Junior Member
Join Date: Jul 2001
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
John A. Oliver is on a distinguished road
Tayana 37 Hawsepipe remove/replace

My pipe does not have through bolts or screws holding it in place. There is evidence of a bronze stub in four places sticking through the inboard side. I have been told that the pipe was probably bedded in place since no screws, bolts, fasteners, etc. are visible. Does that mean you get under the flange with a prybar and work it loose? I would also install some bronze countersink head fasteners to hold the thing in place after removal and re-installation.
Reply With Quote Share with Facebook
Old 08-27-2001
Junior Member
Join Date: Mar 2001
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
Venton is on a distinguished road
Tayana 37 Hawsepipe remove/replace

Not sure on the Tayana, but on my Tashiba the hawsepipes looked like they were not through bolted. However, on very close examination one could see that they where and the heads probably spot welded and then ground flush and polished. It was necessary to drill them out for removal. Once they were out it was obvious. One other suggestion. When I got them all cleaned up I filled in voids (mine were wood blocks between outer and iner hull) with epoxy and used plastic straws as guides for the new through bolts. After the epoxy set, the straws could be removed, worked extreemly well. I then rebedded with new through bolts which were put in the same countersink holes in the pipe and cap.
Reply With Quote Share with Facebook

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools

Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Similar Threads
Thread Thread Starter Forum Replies Last Post
Tayana 42 Center Cockpit goshawk Boat Review and Purchase Forum 7 05-27-2012 07:59 AM
Tayana 42 Offshore ? law0843 Cruising & Liveaboard Forum 2 07-09-2003 07:59 AM
westsail and tayana sdwyer Boat Review and Purchase Forum 10 10-03-2002 12:50 PM
westsail and tayana sdwyer General Discussion (sailing related) 1 06-21-2002 05:04 AM
Tayana 42 Fuel Tank Question jdmrussell56 Gear & Maintenance 2 07-29-2001 07:17 AM

All times are GMT -4. The time now is 03:19 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.