Replacing Chainplates - SailNet Community
 
LinkBack Thread Tools
post #1 of 4 Old 02-09-2007 Thread Starter
I grew up on this ship ..
 
FullandBy's Avatar
 
Join Date: Feb 2007
Location: Vancouver
Posts: 25
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
 
Replacing Chainplates

Well I'm a new proud owner of a Cooper 416. I actually bought her a couple of months ago but have only started working on her in earnest this past week. Weather here in Vancouver has been bloody miserable for the last couple of months so I went away on vacation.

I used to be called MVSunstar on these boards when I was a sailing wannabe, but now that I am I've changed my name and retired the old one.

So on to the real question at hand. My Cooper is over 30 years old and there are signs of some deck delam around the chainplates and some moisture intrusion below decks near the chainplates. The surveyor recommended that I at the very least inspect them. The big problem is that they are completely encased in fibreglass and not bolted through.

So one of my first stupid questions. My mast is stepped on the keel, is it safe to unattach one chainplate at a time to work on it? I basically need to dig out the cold chainplates and replace them all and fiberglass them all in again. A big job.

Cheers
FullandBy is offline  
Quote Quick Reply Share with Facebook
Sponsored Links
Advertisement
 
post #2 of 4 Old 02-09-2007
Member
 
Join Date: Nov 2006
Location: Beacon, New York
Posts: 652
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 9
 
Correct me if I am wrong but doesnít your boat have three chainplates on each side? If thatís true and the mast is on the keel you will not have any problem reworking one chainplate on each side at the same time.

I doubt your chainplates are just glassed in. Under the glass I am sure you will find bolts. Some small boats have plates glassed in but all the larger boats I know of are bolted.
Good luck and all the best,
Robert Gainer
Tartan34C is offline  
Quote Quick Reply Share with Facebook
post #3 of 4 Old 02-09-2007 Thread Starter
I grew up on this ship ..
 
FullandBy's Avatar
 
Join Date: Feb 2007
Location: Vancouver
Posts: 25
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
 
Ya I kind of figured there would be no problem taking one off at a time and yep there are three per side. But just to be on the safe side - the last thing I need is to lose my mast in the yard. I almost lost my boat in the yard last month while I was away on vacation. The genoa broke lose in some hurricane force winds and was threatening to pull the boat over and all those next to me in a very large game of dominoes. The boatyard had to put the haulout machine with the slings on her for a day or two until the winds died down.

As for the chainplates, they really looked like they are just glassed in. There is certainly no bolt going through the hull. However, there maybe bolts going crosswise over the chainplates but are just covered in glass. I guess I will find out soon enough.

Thanks
FullandBy is offline  
Quote Quick Reply Share with Facebook
post #4 of 4 Old 02-09-2007
Member
 
Join Date: Oct 2003
Location: Hampton, VA
Posts: 76
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 12
 
Fullandby, it is a monster job but maybe a necessary one for safety reasons. I was on an IP link/site on repairs of this sort. The one I viewed used x-rays to determine chainplate condition then went from there. Think I was jsut surfing looking at chainplates. There is nothing cheap or easy about it. Like everything else with boats if you have the M&M's it's doable (money & motivation) Good luck

Regards,
Red
Loewe is offline  
Quote Quick Reply Share with Facebook
Reply

Quick Reply
Message:
Options

By choosing to post the reply above you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Register Now



In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.


User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Similar Threads
Thread Thread Starter Forum Replies Last Post
Chainplates Newport 30 MBesant Gear & Maintenance 6 01-22-2009 03:09 PM
Replacing Your Standing Rigging Mark Matthews Gear and Maintenance Articles 0 12-15-2002 07:00 PM
Replacing the Diesel Tank Sue & Larry Gear and Maintenance Articles 0 09-18-2002 08:00 PM
Inspecting and Replacing Lifelines Sue & Larry Gear and Maintenance Articles 0 05-03-2002 08:00 PM
Replacing Standing Rigging Mark Matthews Gear and Maintenance Articles 0 12-22-2000 07:00 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome