Tachometer Calibration - SailNet Community
 
LinkBack Thread Tools
post #1 of 4 Old 03-05-2007 Thread Starter
Voyager
 
voyagersail's Avatar
 
Join Date: Jan 2007
Location: Aboard
Posts: 18
Thanks: 0
Thanked 1 Time in 1 Post
Rep Power: 0
 
Tachometer Calibration

Thought this may of interest to some...

There is a way to check the accuracy of a tachometer using the highly accurate and stable frequency of AC power supplied from any source of commercial shore power. The concept is to use the AC line frequency as the measuring standard. The only tools needed for this calibration check are a piece of tape and a fluorescent lamp which operates from commercial AC line power.

A fluorescent lamp is actually a gas-discharge lamp with the interior of the glass envelope coated with a light-emitting phosphor. When the gas within the lamp is ionized by alternating current it emits pulses of energy. One pulse occurs for each of the voltage excursions of the AC waveform. For the 60-Hz power common in North America, there will be 120 such flashes per second, 60 positive and 60 negative. The pulses of energy created within the lamp excite the phosphor coating, which in turn emits visible light. Because the energy driving the lamp is not continuous, the light emitted is not continuous. The fluorescent lamp emits 120 pulses of light per second, but the human eye's persistence of vision makes us think the light is always on. We can use the pulsing light output of the fluorescent light as a very accurate measuring tool with which to check the calibration of the engine tachometer.

First, obtain access to the front of the engine. Place one piece of white tape on the face of the large pulley mounted on the engine's crankshaft (usually this is the largest pulley in sight). Illuminate the front of the engine with light from the fluorescent lamp. Run the engine at 1,800 rpm, as shown on the tachometer. If the tachometer is accurate, four stationery, or very slowly moving, white marks will appear on the face of the pulley where the tape was placed. If the tachometer is inaccurate, the tape marks may be rotating in either direction. Adjust the throttle until the four tape marks appear to stand still. Note the tachometer reading. If the difference between the reading and 1,800 rpm is at all significant, look for a small adjustment screw on the back or within the body of the tachometer. Turning this screw slightly should make the indicator needle move to exactly 1,800 rpm. If the speed range of the engine permits, increase the engine speed to 3,600 rpm. At this speed, only two tape marks should be visible on the crankshaft pulley. Repeat the check of the tachometer reading and, if necessary, readjust the tach. The basis of this stroboscopic speed calibration is quite simple. At 1,800 rpm, the engine is turning at 30 revolutions per second. The lamp is flashing at 120 flashes per second, or four flashes per engine revolution. Therefore, if the engine is turning at exactly 30 revolutions per second the tape mark will appear four times, with each apparent tape position 1/120 of a second or 1/4 revolution apart. When the engine runs at 3,600 rpm there will be only two light flashes per engine revolution. If the boat is in a country where the standard AC power frequency is 50 Hz, the check speeds would have to be 1,500 and 3,000 rpm since the light would flash 100 times per second.

Voyager
voyagersail is offline  
Quote Quick Reply Share with Facebook
Sponsored Links
Advertisement
 
post #2 of 4 Old 03-05-2007
moderate?
 
camaraderie's Avatar
 
Join Date: May 2002
Location: East Coast
Posts: 13,877
Thanks: 0
Thanked 3 Times in 3 Posts
Rep Power: 16
     
Good tip...thanks!!
camaraderie is offline  
Quote Quick Reply Share with Facebook
post #3 of 4 Old 03-06-2007
can't re member
 
Join Date: Aug 2006
Posts: 318
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 9
 
That's a cool and simple idea. One caveat would be that you should make sure that you are getting clean 60hz power from the dock. I have found fast power periodically, evidenced by the ac microwave clock gaining a couple of minutes per hour. Most power in America is good though.
yotphix is offline  
Quote Quick Reply Share with Facebook
post #4 of 4 Old 03-22-2007
Senior Member
 
pigslo's Avatar
 
Join Date: Nov 2004
Posts: 804
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 11
 
Has anyone tried this? I tried it with aone of the new screw in bulbs and got nothing.
pigslo
pigslo is offline  
Quote Quick Reply Share with Facebook
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.


User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Similar Threads
Thread Thread Starter Forum Replies Last Post
tachometer retrofit for Yanmar YSM-12 Kabloona Gear & Maintenance 0 02-07-2007 02:50 PM
Tachometer morganbill Gear & Maintenance 2 02-02-2007 01:57 PM
Tachometer not working?? bderosa Gear & Maintenance 4 08-02-2006 08:08 PM
diesel tachometer diesel MHRitter Gear & Maintenance 1 09-17-2002 11:52 AM
Digital Diesel Tachometer $65 MHRitter Gear & Maintenance 0 07-24-2002 10:05 AM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome