SailNet Community

SailNet Community (http://www.sailnet.com/forums/)
-   Gear & Maintenance (http://www.sailnet.com/forums/gear-maintenance/)
-   -   And the refit continues... (http://www.sailnet.com/forums/gear-maintenance/54910-refit-continues.html)

CharlieCobra 06-02-2009 09:37 PM

And the refit continues...
 
I've finally finished sanding the deck after pulling the canvas and the varnish removal is 98% done.

http://i234.photobucket.com/albums/e...it%204/007.jpg

The decks were ok except that one chainplate area.

http://i234.photobucket.com/albums/e...it%204/011.jpg

The foredeck is good...

http://i234.photobucket.com/albums/e...it%204/008.jpg

and aft is better than I thought it would be.

http://i234.photobucket.com/albums/e...it%204/009.jpg

Now it's time to sand and seal the bright work, finish stripping the hull, pull the sticks and the engine. I'm gonna seal the deck too before applying the Sanitred.

wlshor 06-02-2009 09:40 PM

Looks great, the hard work is paying off.

smackdaddy 06-02-2009 09:51 PM

WOW Charlie! That's looking great! That Madrigal's got nothin' on you.

PS - Got your message. I'll give you a shout tomorrow. Good work dude!

CharlieCobra 06-02-2009 09:52 PM

I'll be at the boat tomorrow and Jody's supposed to show up. Unless I get an interview that is...

Go ahead and call my cell when ya can.

CharlieCobra 06-03-2009 10:02 PM

Well, Jody showed up and got the AC wired up with a new breaker while I continued to sand and detail the edges. I also managed to get the port handrail off. The giant globs of 5200 promise to be more of an issue though....

JohnRPollard 06-04-2009 10:29 AM

Charlie,

Nice work! She is really coming along nicely.:)

That is a lot of effort, for sure. How are the old back and knees feeling?:rolleyes:

That was nice of Jody to help out with the electrical.

How do you plan to "seal" the decks? Are you going to apply fibreglass, clear epoxy, or something else?

And what did you decide in the end to do with the chainplates? Are you going to go with exteriors?

Mimsy 06-04-2009 10:48 AM

I've said it before, but I mean it. She is going to be ridiculously beautiful once you finish her and you are total stud for DIYing the work yourself. This is not a refit, its a rebuild and you have my utter respect for saving this beauty.

CharlieCobra 06-04-2009 02:36 PM

Quote:

Originally Posted by JohnRPollard (Post 492276)
Charlie,

Nice work! She is really coming along nicely.:)

That is a lot of effort, for sure. How are the old back and knees feeling?:rolleyes:

That was nice of Jody to help out with the electrical.

How do you plan to "seal" the decks? Are you going to apply fibreglass, clear epoxy, or something else?

And what did you decide in the end to do with the chainplates? Are you going to go with exteriors?

Thanks John. The back is better this week and has recovered from my tweaking it last week. Jody's a good pal. I'm putting down CPES to seal and then going with Sanitred over that as it's waterproof, UV proof and flexible. I have an idea about that chainplate and adding exterior isn't on the list. She came around the horn the wrong way with the one's she has so I think they'll be fine.

CharlieCobra 06-04-2009 02:37 PM

Quote:

Originally Posted by Mimsy (Post 492286)
I've said it before, but I mean it. She is going to be ridiculously beautiful once you finish her and you are total stud for DIYing the work yourself. This is not a refit, its a rebuild and you have my utter respect for saving this beauty.

Thanks alot Mimsy. It is appreciated.:D :D

artbyjody 06-06-2009 08:39 PM

Quote:

Originally Posted by CharlieCobra (Post 492156)
Well, Jody showed up and got the AC wired up with a new breaker while I continued to sand and detail the edges. I also managed to get the port handrail off. The giant globs of 5200 promise to be more of an issue though....

Thanks Charlie (everyone)- let me know if there any issues with the new wiring (do not expect any; however, none the less). At any rate glad I was out there - and yep she is coming along pretty fine. Wish I was making as much progress; but, at least now I have an excuse(s) for the time being...

Have fun...


All times are GMT -4. The time now is 09:19 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012