seeking advice with boom, backhaul line need to be retrived. - SailNet Community
 
LinkBack Thread Tools
post #1 of 6 Old 04-10-2011 Thread Starter
Junior Member
 
Join Date: Mar 2011
Location: michigan
Posts: 9
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
 
seeking advice with boom, backhaul line need to be retrived.

Any suggestions for retrieving my backhaul line from inside my boon? On my 1980 Tartan 33, while working to remove the backhaul line which runs inside the boom I temporarily, at least I hope temporarily, have lost it inside the boom. Purpose of removing was to clean it over the winter. My first season with sailboat and I now think I don't need to do that very often if at all. I attempted to remove it by duct taping a small cord to it to so I could refish this spring but in the small cord pulled from the line. The backhaul exits the aft end of the boom. At that point it is a cable. The cable is attached some way to a cord inside the boom as that is what exits the starboard side of the boom toward the mast. that is what I lost. Seems part of the challenge is that also inside the boom run the 2 lines for the jiffy reeling system. The backhaul line seemed to tangle with the other lines.o I would like to do this without removing the caps to the boom if possible. I tried that and they seem difficult to remove.
ambrielt33 is offline  
Quote Quick Reply Share with Facebook
Sponsored Links
Advertisement
 
post #2 of 6 Old 04-10-2011
Just another Moderator
 
Faster's Avatar
 
Join Date: Sep 2005
Location: New Westminster, BC
Posts: 16,534
Thanks: 104
Thanked 312 Times in 300 Posts
Rep Power: 10
     
This is going to be tough to do without removing at least one end cap. The outboard end would allow you to see (maybe reach) the loose end, but the tackle itself is likely anchored to the gooseneck end cap, or to the boom itself towards the mast end.

How difficult this is going to be depends on how far you pulled it though before you lost the messenger.....

Ron

1984 Fast/Nicholson 345 "FastForward"

".. there is much you could do at sea with common sense.. and very little you could do without it.."
Capt G E Ericson (from "The Cruel Sea" by Nicholas Monsarrat)
Faster is offline  
Quote Quick Reply Share with Facebook
post #3 of 6 Old 04-10-2011 Thread Starter
Junior Member
 
Join Date: Mar 2011
Location: michigan
Posts: 9
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
 
Thanks for the info. I wonder if there is a lubricant I could spray where the cap joins the mast. Both are aluminum. The cap is cast. Would wd40 be ok? A little concerned of what should be used if anything.
ambrielt33 is offline  
Quote Quick Reply Share with Facebook
post #4 of 6 Old 04-10-2011
Senior Member
 
paulk's Avatar
 
Join Date: Jun 2000
Location: CT/ Long Island Sound
Posts: 2,605
Thanks: 4
Thanked 26 Times in 25 Posts
Rep Power: 16
 
Before drilling the machine screws that hold on the caps, (WD40 may work, but you will probably not be patient enough to wait that long) see if you can find a steel electrician's snake, which they use to fish wires inside walls. Twist the end around so that it will (hopefully) snag the loose end but still fit through whatever opening you have to work with. Poke it in and use your Zen skills to figure out where the line is. Taking the boom off the mast and turning it so gravity pulls the outhaul to the bottom, or so that it's held up where you can get it by the reefing lines may help. You might also be able to snag it from the other end, pull it out, and then re-snake it. The wire is much better than trying to train a gerbil. When we run messenger lines inside a spar, I try to remember to sew things together, and then tape over it so it slips smoothly over the sheaves. The outhaul may lead through a tackle inside the boom. If the line has come off the blocks inside, you WILL have to remove the endcap(s) in order to re-thread it. We know this because...
paulk is offline  
Quote Quick Reply Share with Facebook
post #5 of 6 Old 04-11-2011
Senior Member
 
JimsCAL's Avatar
 
Join Date: May 2007
Location: Glen Cove, NY
Posts: 2,812
Thanks: 2
Thanked 71 Times in 66 Posts
Rep Power: 9
 
I suspect the end caps are held on by stainless screw into aluminum. Try something like PB Blaster, but I think they will have to be drilled out. Using an electricians fish tape as paulk suggests is a good idea.
JimsCAL is offline  
Quote Quick Reply Share with Facebook
post #6 of 6 Old 04-11-2011
Senior Member
 
Join Date: Jul 2006
Location: Corpus Christi, Tx
Posts: 1,350
Thanks: 36
Thanked 42 Times in 41 Posts
Rep Power: 10
 
If you have to remove the end cap, start with PB Blaster (it won't work) then go to heat, use a propane torch (like you get at the harware stores) and you can probably get the screws out. The end cap may still be well fixed to the boom. Again heat will help.
John
ps. And I like those "Zen skills".
ccriders is offline  
Quote Quick Reply Share with Facebook
Reply

Quick Reply
Message:
Options

By choosing to post the reply above you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Register Now



In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.


User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Similar Threads
Thread Thread Starter Forum Replies Last Post
Boat transport backhaul west to east Beetle General Discussion (sailing related) 1 11-27-2009 09:16 PM
S32 85 and S34 84 have similar specs, seeking advice shaley Sabre 1 09-18-2008 12:54 PM
Single Line Slab Reefing - In Boom jonb Gear & Maintenance 3 04-29-2008 02:58 AM
SEEKING ADVICE! seawindgr Boat Review and Purchase Forum 0 08-31-2002 09:57 PM
Seeking Jib Traveler Advice dchew Racing 0 05-05-2002 05:03 AM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome