Hole in hull - Page 2 - SailNet Community

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Chat  
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance
 Not a Member? 


Like Tree1Likes
Reply
 
LinkBack Thread Tools
  #11  
Old 08-21-2012
Junior Member
 
Join Date: Jul 2012
Posts: 20
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
jfl14609 is on a distinguished road
So much for 5 mins haha I would have to assume this would be more permanent the just pulling the floor board and filling the hole with epoxy
Reply With Quote Quick reply to this message Share with Facebook
  #12  
Old 08-21-2012
Junior Member
 
Join Date: May 2012
Posts: 14
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
Trinidoc is on a distinguished road
Re: Hole in hull

I'm glad this has come up as I have some holes from old seacocks to fill. The old ones had 4 holes and the new ones have 3. My holes are already bevelled from the bolt heads so i think i will use the 105 epoxy mixed with 406 silica to thicken it and some small pieces of fibreglass thrown in for strength. I have to fill my holes from the outside.
Reply With Quote Quick reply to this message Share with Facebook
  #13  
Old 08-22-2012
Junior Member
 
Join Date: Jul 2012
Posts: 20
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
jfl14609 is on a distinguished road
Re: Hole in hull

i think the holes you have are a bit larger than mine is I say 1/4 in but realistically its prob 1/8 i would say a bb would barely fit in it. my original plan before asking people that knew what they were doing was to mix some resin and hardener up then roll up a tiny amount of fiberglass to fit in the hole. then soak it in the resin and stuff it in the hole. seems like others may have better ideas though
Reply With Quote Quick reply to this message Share with Facebook
  #14  
Old 08-22-2012
Junior Member
 
Join Date: May 2012
Posts: 14
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
Trinidoc is on a distinguished road
Re: Hole in hull

How did you get your hole? Was it a drill hole that was filled?
Reply With Quote Quick reply to this message Share with Facebook
  #15  
Old 08-22-2012
Junior Member
 
Join Date: Jul 2012
Posts: 20
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
jfl14609 is on a distinguished road
Re: Hole in hull

it was a small drill they used to allow the boat to drain if any water got in over the winter trust me if that much water got in there (the hole was not well placed) i think you have bigger issues. the hole has never been filled
Reply With Quote Quick reply to this message Share with Facebook
Reply

Quick Reply
Message:
Options

By choosing to post the reply above you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Suspect hole in hull KevinCo Boat Review and Purchase Forum 6 08-20-2012 04:13 PM
Re-using thur-hull hole? Tanley Gear & Maintenance 2 04-23-2011 07:00 PM
Drilling Hole in Fiberglass Hull sailak Gear & Maintenance 16 03-17-2011 10:37 AM
Drilled Hole in Hull Repair weephee General Discussion (sailing related) 22 08-04-2009 11:56 PM
Thru Hull Hole Sizing cas8100 Gear & Maintenance 1 07-10-2009 06:55 PM


All times are GMT -4. The time now is 04:40 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.