MacGregor keel bolts & cables - SailNet Community

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Boat Builders Row > MacGregor
 Not a Member? 


Reply
 
LinkBack Thread Tools
  #1  
Old 01-07-2008
Junior Member
 
Join Date: Apr 2000
Location: FT WALTON BEACH
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
gjmoore2 is on a distinguished road
Send a message via Yahoo to gjmoore2
MacGregor keel bolts & cables

Does anyone know how often these need replacement if exposed to salt water? And how to change our the bolt?

G Moore
Reply With Quote Quick reply to this message Share with Facebook
  #2  
Old 08-07-2008
V25 V25 is offline
Junior Member
 
Join Date: Aug 2008
Location: St Louis, MO
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
V25 is on a distinguished road
I don't know about salt water. I have a '79 Venture 25 and inspected the keel bolt a few years ago. It showed no signs of wear so I put it back in.

I'm assuming you have an older boat with a cast iron keel like mine. To inspect/replace you need to get the boat up off the trailer enough to be able to support the keel in the front and back. It needs to be supported in the back to keep from swinging fore and aft slightly after the bolt is out so that you don't lose track of the hole alignment. In the front support it wit a jack. Put a little upward pressure on the jack to take the weight off the bolt then you can remove the bolt and replace it.

I got my boat up off the trailer by letting the trailer jack all the way down which raises the stearn. Then putting something under the stearn that would hold the back of the boat. I built an oversized A frame type saw horse to fit under it. The screw the trailer jack all of the way up. That gets the rear off the trailer. Then, I used some blocks and put a bottle hydraulic jack under the front and slowly raised the front. I had some 2X4's handy that were long enough to span across the rails of the trailer. As I raised the front of the hull to make enough room I slid a 2X4 under so that the hull (in front of the keel) sat on a stack of 2 - 4 2X4's which were supported by the side rails of the trailer. Just go slowly and have the next board ready to go so that you aren't raising too high for too long balanced on the jack.

Then I could get the jack under the front of the keel to take the weight off the bolt.

Hope that helps,
John
Reply With Quote Quick reply to this message Share with Facebook
Reply

Quick Reply
Message:
Options

By choosing to post the reply above you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Catalina Keel bolts Zevirii Gear & Maintenance 11 08-31-2006 05:08 PM
Keel Bolts Repair/replacement chartscharts Gear & Maintenance 11 08-07-2006 04:53 PM
Keel Bolt Repairs Don Casey Gear and Maintenance Articles 0 11-10-2003 08:00 PM
Keel Bolt Concerns Don Casey Gear and Maintenance Articles 0 10-12-2003 09:00 PM
keel bolts on a P323 jnorth Gear & Maintenance 2 02-18-2002 05:16 PM


All times are GMT -4. The time now is 05:21 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.