Big Black Port Gaskets - Page 2 - SailNet Community

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Boat Builders Row > Morgan
 Not a Member? 


Reply
 
LinkBack Thread Tools
  #11  
Old 04-18-2008
CaptainForce's Avatar
Senior Member
 
Join Date: Jan 2006
Location: living aboard since 1972
Posts: 1,709
Thanks: 0
Thanked 12 Times in 12 Posts
Rep Power: 9
CaptainForce will become famous soon enough
Sue, I've come to the conclusion that the original gaskets were form molded in order to make the 3" radius turn at the ends of the port. I've completed the starboard ports and inserted the locking strip across the horizontal spans of the gaskets tapering them into the curves. I did use a sealant placed inside the ends at the turns just inside the lip of the gasket where it meets the lexan. I also placed a thin layer of sealant against the 1" edge of the hull before laying in the gasket and a dab of sealant where the cut ends of the gasket meet at the top. My stainless steel marlinespike was a better tool to insert the locking strip than the plastic tool sent with my materials. I am very pleased with the outcome both in looks and integrity of the fit. 'take care and joy, Aythya crew
Reply With Quote Quick reply to this message Share with Facebook
  #12  
Old 05-22-2008
Junior Member
 
Join Date: Jan 2008
Posts: 12
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
Orionsue is on a distinguished road
Stewart, we have just ordered the gasket material, locking strip and tool from Griffiths Rubber Mills and will receive soon. Thanks for the advice on how you installed yours. We will be keeping that in mind when we install ours. The people from Griffiths Rubber Mills were extremely helpful. Will send some pictures when we are finished. Have you made any of yours yet?
Happy Sailing!
Reply With Quote Quick reply to this message Share with Facebook
  #13  
Old 05-23-2008
CaptainForce's Avatar
Senior Member
 
Join Date: Jan 2006
Location: living aboard since 1972
Posts: 1,709
Thanks: 0
Thanked 12 Times in 12 Posts
Rep Power: 9
CaptainForce will become famous soon enough
Orionsue, 'best of luck with your project. If you run across another Morgan with the need for the whole length offer them my left over footage with yours. I'd sell under cost just to not carry my left over 40' around.
Reply With Quote Quick reply to this message Share with Facebook
  #14  
Old 05-26-2008
Junior Member
 
Join Date: Jan 2008
Posts: 12
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
Orionsue is on a distinguished road
Thanks Stewart. Will keep you posted on the project and let you know with regards to the leftover gasket material. If you are ever within our waters (Ponce, Puerto Rico) make sure to let us know. Rick and I would be happy to meet you!
Happy Sailing!
Sue, S/V Orion
Reply With Quote Quick reply to this message Share with Facebook
  #15  
Old 10-21-2008
Junior Member
 
Join Date: Oct 2008
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
guardiansolution is on a distinguished road
Morgan h-channel window gasket material

I've also been trying to find the gasket material for my 36 morgan O/I. I've concluded from Orionsue, and Captainforce that the manufacture is Stanlock, and Griffiths rubber mills is a vendor. Appreciate your posting the information because I hadn't been able to locate a vendor or manufacture. If either of you has excess gasket material you'd like to sell before I contact the vendor, I'd appreciate it if you'd contact me at 352-481-2175
Reply With Quote Quick reply to this message Share with Facebook
  #16  
Old 11-11-2008
Junior Member
 
Join Date: Mar 2006
Posts: 19
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
Planb835 is on a distinguished road
I do not have the website available at this time. I did buy some excess marterial from Stuart for my OI33. The tool that worked the best for me was a pair of "ring" pliers. They are used to attach and remove locking rings. I got mine from Lowe's for $19. The greatest part is they have tiny rods to slide into the gasket material and you can reverse the pliers where squeezing the handle opens the jaws. Once you play with them in the store you'll say I got to have these!

Matt
Reply With Quote Quick reply to this message Share with Facebook
  #17  
Old 12-28-2008
CaptainForce's Avatar
Senior Member
 
Join Date: Jan 2006
Location: living aboard since 1972
Posts: 1,709
Thanks: 0
Thanked 12 Times in 12 Posts
Rep Power: 9
CaptainForce will become famous soon enough
Here's my row of new portlights. They're pretty much like the original, but with black instead of white locking strips.


Last edited by CaptainForce; 01-05-2009 at 02:10 PM.
Reply With Quote Quick reply to this message Share with Facebook
  #18  
Old 01-02-2009
ashatsea's Avatar
Living the Good Life
 
Join Date: Nov 2008
Location: St Petersburg FL
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
ashatsea is on a distinguished road
Send a message via AIM to ashatsea
I have been checking out the Stanlock site and I too would like to replace my scary looking port lights. Do you remember what the stock number is that you ordered for your boat I am looking at the different diagrams and i see two types that might work....I have a 33' 73 O/I any help you can offer would be appreciated your port lights turned out great..
Reply With Quote Quick reply to this message Share with Facebook
  #19  
Old 01-05-2009
CaptainForce's Avatar
Senior Member
 
Join Date: Jan 2006
Location: living aboard since 1972
Posts: 1,709
Thanks: 0
Thanked 12 Times in 12 Posts
Rep Power: 9
CaptainForce will become famous soon enough
Ashatsea, Check back soon! I'm sure I'll find it, Aythya crew
Reply With Quote Quick reply to this message Share with Facebook
  #20  
Old 01-05-2009
CaptainForce's Avatar
Senior Member
 
Join Date: Jan 2006
Location: living aboard since 1972
Posts: 1,709
Thanks: 0
Thanked 12 Times in 12 Posts
Rep Power: 9
CaptainForce will become famous soon enough
Ashatsea, The invoice I have for the gaskets is the Stanlock product pruchased from Griffith Rubber Mills, P.O.Box 10066, Portland, Or. 97296, Phone= (503) 226-6971.
The item # for the gasket is 31513SL with the description SL-2026 1/4 x 1
The item # for the locking strip is 37653FTSL with the description
SL-1250 Lock Strip
As you read in the above postings, the gasket replaces the original well, but there is difficulty in applying the locking strip within the 3" radius turns at the ends of the portlights.
Here are views of my portlights before and after:



'take care and joy, Aythya crew
Reply With Quote Quick reply to this message Share with Facebook
Reply

Quick Reply
Message:
Options

By choosing to post the reply above you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Proper use of the Traveler PDixon Boat Review and Purchase Forum 34 04-23-2014 05:00 PM
Crews ready for big day - Port Huron Times Herald NewsReader News Feeds 1 07-22-2007 02:13 AM
Port Hole Gaskets & Teak Veneer Windermere Gear & Maintenance 11 07-17-2007 10:16 PM


All times are GMT -4. The time now is 08:02 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.