Morgan 35 - Boom! - Page 2 - SailNet Community

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Boat Builders Row > Morgan
 Not a Member? 


Reply
 
LinkBack Thread Tools
  #11  
Old 01-01-2009
Junior Member
 
Join Date: Dec 2008
Location: Panama City, Florida
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
Pcrevfl is on a distinguished road
Send a message via Skype™ to Pcrevfl
Now you've got me curious. I will have to see what mine is.
__________________

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Warren
Reply With Quote Share with Facebook
  #12  
Old 04-16-2010
Junior Member
 
Join Date: Dec 2005
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
redg33 is on a distinguished road
Crank

I have a Morgan Outisland 41 with the same boom set-up, does anyone know were I can get a crank for the outhaul?

Thanks,

Bob
s/v Abundance
Reply With Quote Share with Facebook
  #13  
Old 05-11-2010
Junior Member
 
Join Date: Jul 2008
Location: Falls Church, VA
Posts: 9
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
cognomen is on a distinguished road
Crank for Outhaul

I still have the crank -- it also works the centerboard winch (which has lost its sprocket).
I've been thinking I need a spare and was going to try one of two things:
1) a 3/8" Allen wrench, preferably a long one
2) A Stanley awning window crank handle with a piece of 3/8" hex bar epoxied in.

I've tried around the web for a crank handle with a hex end without any luck.
--Nick
Reply With Quote Share with Facebook
  #14  
Old 05-16-2010
Junior Member
 
Join Date: Jan 2007
Location: Vermont
Posts: 10
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
kdstone is on a distinguished road
outhaul crank

I made one out of electric conduit with some slots cut in one end and a rod inserted in the other end. I then found one at a consignment shop so now have both. my outhaul looks like the end of a rod with a pin sticking out on both sides. I am not sure if the hex fitting listed above is a different boom.

Another note our boom is a roller reefing boom and the crank does this also.
KEVIN

Last edited by kdstone; 05-16-2010 at 08:33 PM.
Reply With Quote Share with Facebook
  #15  
Old 01-09-2012
Junior Member
 
Join Date: Dec 2011
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
SammyDPR is on a distinguished road
m35 1971

Does anyone in this thread still owns an M35?

Hi there,

I am looking to purchase an m35 1971. I honestly have a few concerns and would like to ask owners ( or prior owners) about their general experience with the vessel. What to look out for while inspecting it.

1st of all the boat is in the water which there are a lot of things down there that will have to be purchased without inspection. The current owner says that there is no damage down there whatsoever. Also, I noticed that the transom was very thin. Was the transom in yours was very thin as well? I mean the one I inspected was less than a quarter inch thick of fiberglass. How was your experience with that centerboard? The winch of the centerboard is located, in the one I am inspecting, below the port side bench in the cockpit which does not have door/hatch in the bench to access it, to work the winch i believe you will have to crawl into the rear hatch behind the cockpit. Then it goes to a pipe under the engine which makes it even harder to know the real condition of the cable down there. Is that how it was set up in yours?

Did you changed the mast step? The one I am looking at has it very corroded. And to make the work in there it will have thru be done thru the mast hole or break the flooring in the cabin. Any advise on that as well, lol. If we could talk over the phone for a few minutes it would help me and my wife a lot. 1 st purchase an lots of butterflies in my belly righgt now. Lol
Reply With Quote Share with Facebook
  #16  
Old 01-09-2012
Member
 
Join Date: Jul 2008
Posts: 30
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
boofus is on a distinguished road
Sent you a PM
Reply With Quote Share with Facebook
  #17  
Old 01-09-2012
CaptainForce's Avatar
Senior Member
 
Join Date: Jan 2006
Location: living aboard since 1972
Posts: 1,697
Thanks: 0
Thanked 12 Times in 12 Posts
Rep Power: 9
CaptainForce will become famous soon enough
For those thinking of making a handle for the Morgan roller boom, here are a few photos of the original.



Take care and joy, Aythya crew
Reply With Quote Share with Facebook
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Deadly Serious about Booms John Rousmaniere Seamanship Articles 0 10-12-2004 08:00 PM
Control the Wicked Boom John Rousmaniere Cruising Articles 0 05-06-1999 08:00 PM


All times are GMT -4. The time now is 02:39 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.