SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Small outboard plastic prop?
 Not a Member? 


Thread: Small outboard plastic prop? Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
06-24-2013 07:53 PM
ScottyG24
Small outboard plastic prop?

Check your engines height on the transom aswell as u might just be cavitating. Before i was a sailor i spent alot of time on a 75+mph Hydrostream i restored over 3 years and learned rules for O/B props the hard/expensive way:
1. thrust bearing must be good (the rubber i talked about
2. pitch must be correct
3. engine height correct
4.stainless is always best( not an option in this case but just saying)
good luck
06-24-2013 05:26 PM
dabnis
Re: Small outboard plastic prop?

Quote:
Originally Posted by ScottyG24 View Post
Is prop aluminum and when u remove it isthe area where the prop shaft goes into the prop rubber? When props get old that rubber breakdown abd it will cause it to slip reducing thrust. If it is not that you are prob just incorrectly pitched. See what the pitch number should be for your propellor beforeyoubuya replacenent. Plastic props are fine and the flex is built in but they dont last forever
I can only speak from my own experience. I had a Honda 2HP, with the stock plastic prop, for 28 years, put many, many hours on it, broke a number of shear pins on rocky river bottoms. Maintenance consisted of smoothing off the rough edges with a file. Absolutely no problems with the prop, or the motor. Other plastic props may vary?

Paul T
06-24-2013 08:14 AM
ScottyG24
Small outboard plastic prop?

Is prop aluminum and when u remove it isthe area where the prop shaft goes into the prop rubber? When props get old that rubber breakdown abd it will cause it to slip reducing thrust. If it is not that you are prob just incorrectly pitched. See what the pitch number should be for your propellor beforeyoubuya replacenent. Plastic props are fine and the flex is built in but they dont last forever
06-23-2013 08:21 PM
dabnis
Re: Small outboard plastic prop?

I had a plastic prop on a Honda 2 HP outboard. I could actually flex the tips of the prop a little bit with my fingers, so I would guess it would flex under full, load. In any event, it provided plenty of thrust on both a soft floor inflatable and a 12 foot Jonboat. If it is the same or lower pitch as the existing prop it should let the motor rev more at WOT?

Paul T
06-23-2013 08:07 PM
asdf38
Small outboard plastic prop?

So I snagged an Avon Redcrest and a 1976 Johnson Seahorse 2hp from craigslist for $400. I'm pretty happy with the two of them although the redcrest is still a bit too large to comfortably stow on my 26'.

However I took them out on a nearby lake and for the high drag soft bottom inflatable it felt like the engine was overpropped and unable to get to max rpm. Going from 70% to 100% throttle gained little.

While looking for some other parts I noticed that the new props are plastic with an interesting design - sort of long curved blades. It struck me that in practice the plastic prop might flex under load and effectively reduce it's own pitch.

Is the plastic prop actually designed to flex like this or am I overthinking it? Would it be a worthwhile upgrade?



 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 10:12 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.