SailNet Community - Reply to Topic
Thread: Installing an outboard Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
06-25-2013 08:31 PM
Lappy Laz
Re: Installing an outboard

The new engine is a good bit lighter, maybe 10-15 lbs lighter. It is on a lifting bracket which sucks and never lifts out exactly right so I just leave it lowered. While both engines were long shaft, the newer one seems to sit better in the water, or rather deeper. I did decide to tie a rope from the engine to the back cleat in case the whole thing decides to fall off but overall it seems to be the best upgrade I've made so far.
06-25-2013 05:45 PM
Re: Installing an outboard

Although you went to a smaller HP is the 4 strokes heavier / lighter than the old 2 stroke? And is it on a lifting bracket or attached directly to the boat? The reason I asked is I have discovered that my PO install a 4 stroke on a bracket rated for a2 stroke. The bracket springs are not strong enough for a 4 stroke, consequently it is a PITA the lift the motor straight up. I also notice some bounciness in the whole assembly so I have installed extra safety chains in case the whole shebang parts company with the hull. The bracket is # 2 on my replacement list for next year.
06-24-2013 10:33 PM
Re: Installing an outboard

sounds like there was not much left of your 'rude
06-24-2013 08:13 PM
Lappy Laz
Re: Installing an outboard

Engine replacement turned out to be easier than I expected. Thanks for the helpful advice. I went from a 9.9hp (old evinrude) to a 6hp yamaha and it feels like I got twice the motor on the boat now even though its smaller.
06-20-2013 12:20 AM
Re: Installing an outboard

Back the boat into the slip and do it from the dock
06-19-2013 10:47 PM
Lappy Laz
Re: Installing an outboard

That's a great idea. I had not thought of using something that high, that would be great leverage. I don't think the weight will be as big of an issue as just getting over the back end of the boat and getting leverage. Thanks again for the idea that could help a lot.
06-19-2013 10:33 PM
Re: Installing an outboard

Try using your main halyard to support the motor. Use another person at the tail of the halyard and you guide it in place. It has worked for me for that reason.
06-19-2013 10:29 PM
Lappy Laz
Installing an outboard

I'm sure this is posted somewhere but I did a few searches and didn't come up with much so I thought I would ask. So I have an Evinrude 9.9 (old) and just bought a Yamaha 4 stroke 6hp. I plan to replace this weekend on a 27' boat in the water and I'm wonder what advice people give for managing the mounting on over the water. Unfortunately the mount is off to the side of the boat and not the easiest to get over the back to so I am guessing tie a rope incase I drop the engine. It's a 1971 Ercison which had an inboard but removed so everything is a bit awkward about the outboard motor.

Any advice on how procedure people use for swapping motors would be much appreciated.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome