SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  

Quick Menu
Boat Reviews  
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Hatches and Portlights
Interior And Galley
Marine Electronics
Other Items
Plumbing and Pumps
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here

Go Back   SailNet Community > On Board > Gear & Maintenance > eng - trans problem help!!!!!!
 Not a Member? 

Thread: eng - trans problem help!!!!!! Reply to Thread

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

Topic Review (Newest First)
01-30-2002 02:14 PM
eng - trans problem help!!!!!!

I fixed the last problem. now i am unable to remove the damper plate from the flywheel.. rusted tight... I was told that I may as well just rip it off and replace the plate, which is I understand is about $100.00... what do you think??? firemanbob
01-21-2002 03:42 PM
eng - trans problem help!!!!!!

Yanmar usually applies a transmission from its subsidiary Kanzaki and with gears, etc. from Hurth Transmission.
Typical Yanmar transmission dissassembly requires a special set of tools to remove the output shaft nut from the output shaft.
For example the 2QM20 requires special wrench #177099-090910 and special coupling lock #177099-09020 .... this will get the output coupling disconnected, then its a simple dissassembly once you get the shifting fork disconnected. For a 3QM30: special wrench #177090-09100, and coupling lock #177090-09140.
Be careful, as the Kanzaki Transmission requires a lot of special tools, etc. to properly disassemble,etc.
If you''re located on the East Coast, contact Mack Boring Co. in NJ who is the master distributor for Yanmar for the eastern USA ..... also get the service manual, to make your life easier in itemizing the special tools needed, the sequences and other specs. What you are about to undertake is a near impossibility without the special tools required.
01-21-2002 01:00 PM
eng - trans problem help!!!!!!

have a 30 pearson and it has a yan-mar eng and odd ball japanise trans.. after extracating the pair from the eng compt i find that i am unable to seperate then. so i guess that the splined shaft is fused in place. any ideas????? firemanbob

Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

All times are GMT -4. The time now is 10:11 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) LLC 2000-2012

The store is owned and operated by a company independent of the forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.