SailNet Community - Reply to Topic
Thread: Patching water tank? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
01-03-2008 06:19 PM
deerenick I have repaired leaking plastic fuel tanks with the expandable plugs that you can get at the hardware,you must first drill a clean hole through the old one then insert the plug and tighten the machine screw to expand the plug.I would replace the plated screw with stainless.(note)will only work with a punched hole and not a crack line.Good luck.Bill NC
05-08-2007 03:00 PM
sailingdog HS-

BTW, there are a few epoxy mixes that are rated for food area/potable water area use. Most are not though. Ice is also a good abrasive for cleaning out water tanks.
05-08-2007 02:48 PM
hellosailor Tom, I think the tanks are usually rotomolded polythene and not much bonds to that. There are some new epoxy sticks (i.e. like plumber's putty) that are targeted for PVC and other plastics but I don't think polythene is on the list, or that the epoxies are rated for drinking water use.

Traditionally you would buy a plastics welding kit, which includes a heat gun and plastic rods. Match the rod to your tank material and you literally weld in new plastic to fill the crack/hole and if you've done it right, you have it repaired.

But the simpler and cheaper route is probably to apply a patch or plug, which is a perfectly good permanent solution. If the hole is small, install a stainless or nylon bolt through it with a rubber or buna o-ring under the head, end of story. If there is a crack, not hole, drill a hole to relieve the stress at each end o fhte crack, the bolt a small stainless plate over it (plate inside the tank) with 4-6 bolts holding the stainless over a piece of gasket material. Again, end of story.

The tank CAN certainly be repaired, you just can't crazy glue it and walk away.

One way to clean a tank that you can't reach inside of, is to use something like Polident and let it soak. Or, pour in coarse rock salt (deicing salt) or coarse koshering salt, and vigorously shake the tank. The salt crystals are just as sharp as an abrasive media--but you can water-wash all of them out afterwards.

"Makes sense: how could this stuff leak, without impact? " Bad casting. The folks who make rotomolded kayaks claim they have an incredibly large defect rate from bad castings, so they have to charge high prices for the ones that are cast properly. (Ahuh.)
05-08-2007 02:15 PM
geary126 very clever, Mr. Bond...!

I'll have to look into this. Could be the answer. Makes sense: how could this stuff leak, without impact? This plastic looks pretty bulletproof, especially with water only.

Thanks, y'all. Will report back.

Open to cleaning suggestions.

Also: what to do with bow tank? remove and clean, or just clean in place?

Also (2) you guys use normal clear hose, or the reinforced stuff? Given that this is non thru hull related, seems like I could KISS.
05-08-2007 01:31 PM
TrueBlue I removed a plastic water tank from a previous boat once and discovered blobs of caulking like substance adhered to the sides. This was apparently an attempt by the builder to dampen and isolate the tank from the hull and bulkhead it was attached to.

Is it possible that your "1" round blob" is not a patch, but an isolator of sorts, used to minimize vibration?
05-08-2007 01:22 PM
sailingdog One way to patch polyethylene tanks that is a bit off the beaten path is the "candles" that they use to patch alpine ski bottoms. The bottom surface on alpine skis used to be a form of polyethylene or similar plastic... and we used to fill the gouges using a "candle" that was made of plastic and wax combined, and dripped the plastic into the surface and then filed the repair flat. I don't know if they still make the patching sticks, but if they do, they might be worth a shot.
05-08-2007 01:09 PM
geary126 okay. Good point. My To Do list is already daunting!
05-08-2007 12:15 PM
sailingdog The tank is most likely polyethylene...not polystyrene... which is a lousy choice for potable water tanks. I believe epoxy will stick to it...but not very well.

Why are you assuming the tank needs to be patched... I wouldn't worry about that until you know the tank leaks.
05-08-2007 11:28 AM
rheaton You might want to test the tank to see if it leaks. If you have access to a preasure tester, use this. If not, perhaps you could seal the fill hole, and hold the tank under water looking for bubbles from the suspected area. If no leak, then you have nothing to fix.
05-08-2007 11:22 AM

I am a total noob but your mention of sticking a brush in the tank reminded me of something. At a martial arts school I went to they had a water cooler with a 5 gallon plastic water container on top that they would refill rather than have a service replace. After awhile it would get pretty slimy on the inside and to clean it they would put ice cubes in it with soap and swirl it around. Worked very well and the ice could just be dumped out.

I can imagine the tank you are talking about is much bigger and would require some engineering to "swirl" it but most any problem involves trading off time and money and hey it could be fun.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome