SailNet Community - Reply to Topic
Thread: Mooring systems Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
08-25-2015 09:36 PM
Re: Mooring systems

The recommendations for a mooring are all over the map, with "official" sources citing wildly different things. Also, some of the recommended lengths of chain will see you swinging into your neighbor (or with chain 4 times the depth of high water probably well behind your neighbor). As with anchoring, it would be great to have long scope but it is just impossible in many real world settings. Second, in my humble opinion the bottom must be a critical factor, in addition to the type of bottom anchor and weight. Here, in Sidney BC, the bottom is mucky. The standard mooring is a 5000 lb marine concrete block. Now some people will say this will drag. However, a few months after this has been on the bottom, it is impossible to move, even with the small tug that sets them. It's not going anywhere. My neighbor has this, with a 50' ketch, and storm force winds are common in winter. When boats break loose, it is almost always the pendant that has chafed through. Swivels are seldom seen, local thought being a weak link is far, far worse than the potential problems from twisting (which for some reason does not happen too often). There is only one length of chain, that goes through a cast hole in the concrete block up to the mooring ball, at about 1.5 -2 times high water depth. Again in spite of this being insufficient according to some opinions, these things never, ever drag, and are drastically cheaper than the complete "system" the "expert" (salesperson) will sell you at the marine store. Still, I'm thinking of installing a really big, oversize top swivel (as often seen in the UK) to go with my double pendant (slightly different lengths) and extensive chafe guard.
05-23-2015 06:48 PM
Re: Mooring systems

Good article.
10-09-2007 09:05 PM
CapnHand "A winter stick is simply a length of 4 x 4-inch lumber sufficiently long to remain well above the surface of the water during the winter." ater.jpg

Yes, it's all but invisible.
09-22-2007 08:13 AM
Originally Posted by RickBowman View Post
The winter stick sounds like a good way to crreate a navigational hazzard to other vessels.
Ice will not stick to a wooden winter stick.
09-22-2007 08:13 AM
windship The American Made mushroom is counter weighted. This will yeild different results, and the total length of primary and secondary chain and the length of the pennant will also yeild different results.
08-31-2007 04:59 PM
Mooring systems

Mooring systems
How to make sure your boat stays put
by Bill Sandifer

Not long ago I spoke with a sailor who had a 27-foot Sabre moored on a 250-pound mushroom mooring anchor as recommended by the local yacht club and the municipal harbormaster. During a big storm, his boat dragged and was destroyed on the rocks. He asked what kind of mooring to use in the future. Before offering suggestions, I did some research about mooring systems. Not much information was available.

Mushroom anchor

Most of the information we rely on seems to be based on the recommendation of some trusted source, such as a harbormaster or a local yacht club. Even Chapman's Piloting, Seamanship and Small Boat Handling has just a limited discussion of "permanent moorings" and offers a small table showing the recommendations of the Manhasset Yacht Club of Long Island, New York. These recommendations are good for their area but should not necessarily be trusted in other areas.

In deciding on a permanent mooring for your boat and location, consider the type of sea bottom, current, exposure, prevailing winds, water depth, tides, and swinging room. Also, try to get some local knowledge.

Local knowledge

When I was a kid in Oyster Bay, New York, I had a 16-foot outboard boat on a mooring. I had a lot of discussions with Conrad, the local mooring guy, who set all the larger moorings in the harbor. He advised me on the type of mooring anchor to use and where to put it. His sole business -- other than a little winter fishing -- was setting and retrieving moorings. He charged a moderate sum to set a mooring in the spring, equip it with a new pendant every year, and pull it out in the fall before the harbor iced over.

He knew by long experience what size mooring to use for what size boat. He took into consideration the windage of each boat and used a heavier mooring anchor for boats with more windage. Conrad knew the composition of the bottom and the best place for each boat. He was a qualified harbormaster long before the term was coined.

There are three basic types of permanent mooring anchors in common use. These are mushroom, pyramid, and dead-weight anchors. In addition, some moorings use three anchors set at 120 degrees to each other with chain leading to a center point, and some moorings use a helix screwed into the bottom.

Mushroom anchors – The sailor whose boat had dragged had used the correct sources to arrive at his mooring system, but it was nevertheless not heavy enough or well enough dug in for the big storm that destroyed his boat. Digging in is important; otherwise, a mushroom anchor may skid and roll along the bottom. It's not common knowledge that a mushroom anchor must be tipped over and "set" in the same way that one "sets" a conventional anchor. One improvement for mushroom anchors is a new variety of these anchors with weights placed on the shank to help them lie horizontal.

Pyramid anchor
Granite block

Pyramid anchors – A relative newcomer to the field is a pyramid anchor similar to the old lead sinkers we used when bottom fishing as kids. Due to their shape, these anchors must lie on their sides and present a flat edge to the sea bottom when pulled against. My mooring in Mississippi for a previous boat was a triangular version of this anchor and worked very well (see article in Good Old Boat, January 2002). I set it in mud, but it would have done as well in soft sand or silt. I do not think it would have been as successful on hard sand or weeds.

Dead-weight moorings – One other reliable mooring used with hard bottoms is the dead-weight type. Some folks in Maine use granite blocks with a hole in them as mooring weights. These serve well but are very heavy . . . on the order of several tons. These weights must be set by a barge and crane or tripod. If enough wind is blowing they can still drag, but even when they drag they offer considerable resistance and drag slowly enough for the boatowner to make the necessary adjustments or move the boat to a safer mooring.

Three-anchor mooring – Another way to make a permanent mooring is to use three conventional anchors set in a circle at 120 degrees, each shackled to a common center chain. This system ensures that there is always an anchor upwind of the boat, no matter which way the wind blows. Since it takes three normal anchors of a large size to make it effective, this system is more complicated to set and more expensive to install. Each anchor in the set must be large enough to hold the boat in storm conditions.

Helix anchors – The helix screw anchor was developed for hard sand or weeds and other difficult-to-penetrate bottoms. This is a bigger -- a lot bigger -- version of the screw-type dog anchor found in pet stores. The principle is the same. The helix screws into the bottom and is prevented from pulling out by the wide flukes of the screw bit. These anchors must be set by commercial firms and are usually left installed in the bottom from season to season. Small versions of the helix can be set by divers in shallower water.

Weight considerations

The first thing to remember when considering the weight of a mooring is that everything weighs less in water than it does in air. It may not float in water but it definitely weighs less. It's a question of how much less.

Helix anchor

Underwater weight can vary quite a lot. Some materials weigh 50 percent less in water than they do in air; some may weigh 30 percent less. In water, concrete loses almost one-half of its weight, granite loses more than one third, and iron loses an eighth of its weight. These are significant losses, particularly if the anchor is of the dead-weight type.

Since iron, as used in mushroom anchors, weighs 12.5 percent less in water, a 300-pound mushroom really weighs 262.5 pounds when submerged. Cinder blocks, cement, and old engine blocks are subject to the same laws of physics. Whatever weight you use must be proportionally heavier to give you the desired weight under water. This is why the experienced Maine mariners use several tons of granite to hold their boats on the hard and rocky bottom.

When I was a kid I built a dock using large granite rocks from the beach. I could not lift these rocks when they were exposed at low tide, but I could clear the sand from around them and, as the tide came in, I was able to move them to my construction site under water. I could never bring them above the water's surface, but I successfully built a pier with them. The hardest part was finding small enough rocks to build the above-water part of the pier. I did it and filled the center of the pier with cement. The pier is still there all these years later.

The weight of a mushroom anchor must be calculated as "dead weight" until it has dug itself into the bottom. The holding power of a mushroom that is not set is, at best, equal to twice its weight. When properly set, its holding power can increase to 10 times its weight, but once it's broken out of the bottom again, it will not reset. Instead, it will slide or roll over the bottom.

Take the case of an average 40-foot vessel in a 64-knot blow. The wind load on this boat will reach 5,500 pounds. While a 500-pound mushroom might seem to be enough for this boat, a 500-pound mushroom (438 pounds actual underwater weight) fully dug in will resist 10 times its actual underwater weight, or 4,380 pounds. If the load goes over 4,380 pounds, the mushroom will pull out of the bottom and offer little resistance as the boat drags it along the bottom. This is what happened to the Sabre 27.

Comparison test

In a comparison test held in Vineyard Haven harbor, the helix showed outstanding holding results. A 350-pound mushroom set 5 feet deep in mud required 2,000 pounds of force to pull it out. A 500-pound mushroom set in a sand bottom required 1,700 pounds to break it out. A 3,000-pound concrete block set in mud required 2,100 pounds to break it out. A 6,000-pound concrete block on a sand bottom required 3,200 pounds to break it out.

"The first thing to remember when considering the weight of a mooring is that everything weighs less in water than it does in air."

Compared to these, an 8/10 helix set in soft clay mud required more than 20,800 pounds to break it out. The "8" in this description refers to the bottom helix, which is 8 inches in diameter. The "10" refers to the top helix, which is 10 inches in diameter. Typically, shaft thickness is 1  1/2 inches in diameter. The shaft length varies depending on bottom soil conditions. Boats moored over a firmer soil will get by with a shorter shaft. Looser soils will require a longer shaft. In looser soils, there may be more than two helixes on a shaft.

The helix is strong, long-lived, environmentally friendly (as it does not drag over the harbor bottom), and some insurance companies give a premium discount when you use one as your mooring anchor. When the contractor installs a helix, he can accurately predict the amount of resistance needed to pull it out. This gives a great degree of assurance to the boatowner.

Personal preferences

Of the five mooring systems, I like the helix best. But pros who set helixes are not available in every harbor. The pyramid would be my second choice, the three-anchor combination next, and the weighted mushroom fourth. I do not consider the un-weighted shank mushroom to be reliable unless it is carefully set by a knowledgeable person.

For the sailor whose boat had dragged, I suggested a 500-pound pyramid anchor for his intended 30-foot replacement boat. This mooring should have a length of heavy 3/4-inch chain equal to the high-water depth plus 5 feet. Connected to that, 1/2-inch chain should be at least twice the high-water depth. The mooring buoy should be connected to the lighter chain with a swivel. Then a minimum of 10 feet of 3/4-inch three-stranded nylon pendant with chafing gear should finish the mooring by also connecting to the swivel. If there is insufficient swinging room for this mooring, the pyramid should be 50 percent heavier for safety reasons.

Overkill? Perhaps. But it's cheap insurance for a boat. A three-to-one scope will let the angle of pull from the mooring to the cleat on the boat's deck be reasonable. Anything less than three-to-one and the angle will get too steep and create more lift than straight-line pull. Remember that lift will break out the best mooring anchor. When calculating the amount of scope, the height of the bow must figure into the equation. Some boats have a bow 3 or 4 feet above the waterline. If a boat is moored in 20 feet of water at high tide and the bow is 4 feet above the waterline, it needs 3 times 24 feet for a correct three-to-one scope.

One of the ways to alleviate a short scope problem is through the use of a kellet. This is an additional weight shackled to the anchor chain about 10 feet from the anchor to help decrease the angle of pull in all but the most severe storms.

A kellet provides a catenary to absorb some of the shock. In addition, a three-stranded nylon pendant will act as a shock absorber and decrease the shock on a mooring. A safety pendant, 30 percent longer than the everyday pendant, will provide extra safety if the primary pendant fails. If this occurs, the longer pendant will increase the scope in a blow just when it's needed.

Seasonal considerations

If you have a year-round mooring, it will have more time to dig in and acquire greater holding power. In areas where the water freezes each winter, such as Maine, a winter stick can replace the summer mooring buoy for better ice protection. A winter stick is simply a length of 4 x 4-inch lumber sufficiently long to remain well above the surface of the water during the winter. There is little for the ice to grab on to, so a winter stick is suitable for marking your mooring all winter long. In some areas, a group of moorings are left over the winter and located once again in spring because they are chained together with the chain led to a piling.

The ways to maintain a mooring are limited only by your imagination. My mooring is left fully submerged all year long and shackled in winter with old stainless-steel rigging wire led to a tree near the water's edge. Each year when spring arrives, I can easily find the mooring, check the lighter chain, replace that if necessary, check the heavy chain, and lubricate the swivel.

A proper mooring requires a bit of work and additional maintenance expense, but the end result -- a secure mooring for your boat -- is worth the effort.

Note that the Manhasset Yacht Club mooring recommendations below are based on 20 feet nominal water depth with a minimum scope of 3.5-to-1 to as much as 4.5-to-1. There is no 2-to-1 or 2.5-to-1 in the table, regardless of boat size.

If I were to moor in similar conditions, I would follow the Manhasset Bay Yacht Club recommendations, except that I would want to use a helix, if available, or a pyramid, if a helix were not available.

Finally, even with the best mooring in the world, there is always the danger of some other boat dragging down on your boat and both dragging away. Choose your mooring neighbors carefully and help the other sailor with his selection of a mooring. This way both boats will be safer.


Helix Mooring Systems
P.O. Box 723, Belfast, ME 04915; 207-338-0412;
Toll-free: 800-866-4775; Fax: 207-338-0415

The author:
Bill Sandifer (Mooring systems, Page 29) is a contributing editor with Good Old Boat and a marine surveyor and boatbuilder who has been living, eating, and sleeping boats since the early '50s. He and his wife, Genie, sail an Eastward Ho 32.

Posting Rules  
You may not post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome