SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  

Quick Menu
Boat Reviews  
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Hatches and Portlights
Interior And Galley
Marine Electronics
Other Items
Plumbing and Pumps
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here

Go Back   SailNet Community > On Board > Gear & Maintenance > Delaminated Rudder Chapter II
 Not a Member? 

Thread: Delaminated Rudder Chapter II Reply to Thread

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

Topic Review (Newest First)
10-27-2002 01:46 PM
Delaminated Rudder Chapter II

I have a tartan 34''and have some gelcoat cracks that run across the nonskid area in my cockpit. I was wondering if anyone knew a way to replace the nonskid pattern after I fix the cracks. The crack repairs I can do, I''ve done them with success in the smooth gelcoat on my boat, but the nonskid stumps me. I really don''t want to sand it all off and paint it with a nonskid powder. I have heard of some builders being able to send you a small mold to lay down on the wet gelcoat to reestablish the nonskid, was this a fable or am I on the right track.
10-22-2002 05:36 AM
Delaminated Rudder Chapter II

My core looks nothing like foam nor does it have any structure to it that could be called cells. I don''t think crushing it is a problem as it is very hard.
10-20-2002 07:09 AM
Delaminated Rudder Chapter II

what you found is open cell structural foam. strong but sucks up water like a sponge. It has its uses but I don''t like it. in a rudder you have two things working against you. you have a structural foam and FRP that have a differant coefficient of expansion than the stainless rudder stock. this always creates a crack where the stock enters the rudder and provides a path for water to get inside the rudder. I wish i had a definative answer for all but i don''t. obviously if the rudder fills with water its subject to freezing and bursting if it doesn''t drain. it can also cause constant blistering because it never drys out. On mine I finally bite the bullet, removed the rudder, split it and removed all the open cell foam. I then used FRP to make a much larger load area for the foam. glassed it back together and filled with closed cell foam. its not as strong as the open cell but I don''t have a problem with water in the rudder now. this is a large project but if your handy doable.
the key is to make sure that you have increased the load area enough to assure that you won''t crush the closed cell foam inside. I did this 8 years ago and havn''t had any problems since.
good luck.
10-19-2002 06:52 PM
Delaminated Rudder Chapter II

I took the predominant advise and pulled the rudder - a lot easier than I anticipated. Using a dremel I cut around the area and pulled off the outer skin. Inside was not what I expected. When I have read about foam cores I imagined a foam like material not terribly unlike styrofoam or Great Stuff. The core of my rudder seems to be some type of epoxy or polyester. It is hard - I figured foam would be somewhat easy to cut, etc. There are some random glass fibers in the mix. It is almost like Irwin took a batch of left over resin to use as the core. Any thoughts? I am considering using West to fill some of the voids that exist in the core.

Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

All times are GMT -4. The time now is 12:56 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) LLC 2000-2012

The store is owned and operated by a company independent of the forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.