SailNet Community - Reply to Topic
Thread: PS 37 Cutlass Bearing Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
01-15-2008 03:03 PM
AjariBonten Hi PSC, welcome aboard.

That is a really ingenious way to handle that situation. It seems like replacing cutlass bearings is either "no problem" or a "total PIA" depending on the circumstances. I've done it twice (lobster boats) and had one of each experience.

30 minutes once, 3 days the other.
01-15-2008 02:38 PM
How to remove Cutlass bearing?

I own a Crealock 37 Hull # 242.
I replaced the cutlass bearing without removing the rudder.
Remove the prop and look first, how much of the cutlass bearing is exposed? If it exposed more then ” than I believe, that you can do it.
I bought a 1and a ” cast iron coupling (Home depot) . I drilled and tapped 8 holes around for a 8/32 machine screws, ” from one end of the coupling. Than I grind the tips of the screws to a point, to make them work like a set screws.
After removing the small screws that hold the cutlass bearing to its place, I installed the coupling and the set screws into the exposed cutlass bearing. (Try to grip the cutlass as far from the end as possible.) I tighten the screws real good, and than, using a prop puller, I pulled on the coupling and got the bearing out. It takes few minuets, once you have the coupling ready.
The Cutlass bearing is: 1"x1 3/8"x 4"
12-14-2007 11:15 AM
PSC37 cutlass


I own hull #372 (recently purchased) with ~1000 hours on my Yanmar 4JHE. I just replaced the cutlass bearing (which was in bad shape). The yard told me they completed the job in 30 minutes (incidently, the yard who hauled me for the survey told me that they would likely need to remove the rudder - happy to say , I did not use that yard!). Sorry I cannot help you with the dimensions.

Ken Eckert
Moss Landing, CA
11-20-2007 09:09 PM
Hours on diesel

We have 830 hours on the engine
11-19-2007 07:52 PM
arisatx Roland:

I can't help much in answering your question, but I am interested in hearing everyone's feedback, as I believe I'm not too far behind you with #359.

How many hours do you have on your PSC, may I ask?
11-19-2007 07:42 PM
PS 37 Cutlass Bearing

I need to replace the cutlass bearing on our PS 37 #347. I would like to have the replacement bearing in hand when the boat is put on the hard. I know the shaft is 1 inch but need to know the outside diamenter of the cutlass bearing. If you have replaced the cutlass bearing on a PS 37 and know the O.D., I'd sure like to hear from you.

Also, if you have changed the cutlass bearing without dropping the rudder, I'd really like to hear how you did that.

Roland Snyder
Wayward Wind
PS 37 #347

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

For the best viewing experience please update your browser to Google Chrome