SailNet Community - Reply to Topic
Thread: Install electric windlass Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
04-12-2003 03:33 AM
Install electric windlass

Some boat manufacturers set up the windlass circuit so that you can only operate it when the engine is running...That seems like a pretty good idea since it would keep you from accidentally running down your battery and being unable to start.

If you choose this option I''d use the starting battery to run the windlass.

I had the good fortune to have a friend suggest that I get the manufacturer to pull the wires when the boat was being built. I have 02 wires to the chain locker. That should be plenty to run my lighthouse windlass.
04-11-2003 11:58 AM
Install electric windlass

I mounted an Ideal Vertical Windles. I placed it on a Teak pad and installed 2 foot pads to raise and lower the anchor. I ran double ought (00) wire from the cockpit locker were I mounted the breaker panel, solinoid etc. I used regualr battery cble from breaker panel to a 4D battery. Worked fine but running the double 00 wire was a pain. When completed no wire visible inside the boat and a neat, trim job on the bow.
04-11-2003 01:07 AM
Install electric windlass

What ''fer'' said.
30 Sq. mm is roughly equivilent to #3 AWG cable.
Assuming a 100 Amp load @ 12VDC, you would begin to exceed 10% voltage drop @ < 70 circuit feet, that is pos. + neg. @ 35'' from source.
See the article "Ohm''s Law & Boats" in the March/April issue of "Good Old Boat Magazine"
04-10-2003 07:10 PM
Install electric windlass

Congratulations for your new horizontal electric windlass. I can imagine your wife is also very excited about, specially considering how nicely fits in the bow, even she couldn''t get her sun bath confortably as before. How sweet.

OK lets got back to work. Option 1 Mounting a dedicated battery in the bow area, will put some weight in the bow area where you don''t want more weight. ANd additinal dollars in other battery.

Option 2, which I support, will allow you to run your windlass either from golf bank or the starting one, or both. I do personally preffer powering the windlass with the starting battery, with the engine - alternator running too. On top of that, the latter one is an easier installation.

Foot switches and or remote control power the solenoids. And solenoids located near the windlass.

I am running a 1500watt windlass with a 30 square milimiter section cable.(I don''t know the equivalent American cable code)
04-09-2003 03:56 AM
Install electric windlass

I think if you price the two wire sizes you''ll find that there is a big difference in price. But if you have to run cables anyway (bigger ones will be much harder, though) and you don''t care about price, run it from the ship''s battery.
04-09-2003 01:48 AM
Install electric windlass

You might also consider Option 3 - supply from starting battery.
Would not add a dedicated winch battery.
04-08-2003 05:30 PM
Install electric windlass

I just acquired a used Ideal CWM horizontal electric windlass. It fits nicely on a plate attached over my bow sprit of my Westsail 32. It fits nicely between the staysail boom post and the Samson posts.

My question is should I use option 1 or 2 below or other to provide power.

Option 1 - Mount a battery dedicated to the windlass in the bow area. There is no ovious location. The battery can be a mosest size as it is only expected to operate for about 5 minutes when retriving the anchor. Will require fairly heavy wire from alternator to charge it.

Option 2- Power the windlass from existing house golf cart battery bank usiing separate switch and breaker. This will require heavy heavy battery cable for the approximately 50'' run of plus and minus cable.

Additional components needed for either option are the control switch and power solonoid.

The cost difference doesn''t seem too great between options at this point and probably not the biggest factor. I am lookinig for safety and ease of installation.

Thanks your for experience, ideas and opinions.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome