|Topic Review (Newest First)|
|03-23-2008 09:01 AM|
|Perithead||Thank you all for the ideas. They sound pretty good. Ill give it a shot and lt yall know how it went.|
|03-19-2008 09:40 PM|
Another option is to use a drain fisher...depending on the size of hole - they will bend the 90 degrees fairly easy.... however a cheaper solution if you have not pulled the wire - is to use dental floss...it has enough tensile strength --- punch a small hole in the insulation of the wire and tie off in a knot through the hole naturally. Pull existing wire out... repeat procedure for the new wire and pull back up...
just a suggestion and something I do to run wire on occassion in tight situations.......
|03-19-2008 09:27 PM|
The combination of shop vac and cotton / floss might actually have something going for it....I might even make that my 1st resort.
|03-19-2008 09:06 PM|
|wchevron||my surveyor told me this so i haven't tried it yet. remove the old wire, from one end insert a piece of thread, something heavier than clothing thread. on the other end attach a wet/dry vac. it should pull the thread through into the wet/dry vac. loop the end of the wire over. tie on the thread, cover with elec tape and pull through.|
|03-19-2008 07:49 PM|
As a last resort you could try the cotton ball and dental floss trick; that's where you tie the end of a piece of floss to the cotton, stuff the ball into the hole and blow hard. Maybe air pressure will work for you......I said it was a last resort.
|03-19-2008 07:34 PM|
You need to contact sailhog, who has a very close colonoscopy doctor friend who is always willing to stick his scope into tight places.
I understand these devices have a light and video camera at the end, along with a remote tool with various attachments, such as forceps and unmentionables. No problem snagging that elusive wire with this guy.
PM sailhog for details on how to reach him.
|03-19-2008 07:31 PM|
|camaraderie||I think a long but flexible wire that you can use to fish the new wire down below is what is needed. Clutch control cables interior wire works well for this and most boat yards have some old one lying around from engine repairs. Failing that you are faced with either a complete removal of the pulpit OR making a new deck exit for the wire with a hole and cable clam and running the wire up the pulpit from there. No fun unless you get lucky with the "fish" wire!|
|03-19-2008 07:15 PM|
|sailingdog||The problem is if the wire is actually making a 90˚ turn, most things, including house wire, electrical fish tapes, and such, won't be able to make the turn successfully.|
|03-19-2008 06:46 PM|
Try this. If it works, great. If not, them you're no worse off than you are now.
1. Pull the old wire through the bottom of the pulpit. You already have the pulpit unbolted, so it should be easy. Pulling is far easier than pushing!
2. Pull the ground wire from a length of stiff house wire (single strand 10 or 12 gauge). It's uncovered, so you won't have to strip off the plastic coating.
3. Push it through the hole where the bow light wire should be toward the base of the pulpit. It's stiff enough to push past the elbow.
4. When it exits the bottom of the pulpit, put a small hook on the end with a pair of needle nose pliers.
5. Clip the old wire, but leave enough to attach a new length of wire to it. That is, don't clip it flush with the deck!! Don't do this step until you complete step 3, or you could be screwed.
6. Attach the new wire to the old one using proper splicing methods.
7. Strip off about an inch of insulation from the other end of the positive and negative strands of the new wire and join them making a sort of loop. Hook the loop over the hook in the stiff wire and neatly wrap the joint with duct tape for strength
7. Pull through from the bow light end.
|03-19-2008 05:50 PM|
Well, I tried both running a new wire and pushing it up through bottom this past weekend.
The problem with running a new wire is that it has to a 90* turn in order to go down th ebow rail, and I couldnt get it to do that. Then, I took the one base of the railing up a little and attempted to push the wire but couldnt get good leverage on it. I would have to take the railing completely off probably to do that.
Someone suggested to me to try an electrition's fish?
|This thread has more than 10 replies. Click here to review the whole thread.|