SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Chat  
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Strength of tapped bolts versus piloted sheet metal screws
 Not a Member? 


Thread: Strength of tapped bolts versus piloted sheet metal screws Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
02-01-2009 11:11 AM
SimonV If you drill out the glass pot with resin then drill and tap with a course thread it will hold beter than just glass. But you will need plenty of meat around the screw.
01-31-2009 05:35 PM
timebandit Something I use--

After setting the screw remove it and put a drop of super glue in the hole and allow 24 hrs. before reinserting.

Quote:
Originally Posted by GBurton View Post
Yes - of course a backing plate and through bolted is the way to go, but not possible in all applications. I'm leaning toward the pilot drilled SS sheet metal screw......thanks for the help.

P.S. Sailingdog - couldn't stay away could you
01-31-2009 03:48 PM
GBurton Yes - of course a backing plate and through bolted is the way to go, but not possible in all applications. I'm leaning toward the pilot drilled SS sheet metal screw......thanks for the help.

P.S. Sailingdog - couldn't stay away could you
01-31-2009 03:24 PM
Omatako Glass fibre never holds a fastener tightly for long and will wear away with even minute movement and a fine thread will leave very little "meat" for it to be strong in GRP (OK in metal). So a fine thread on a bolt will let go first, a course thread on a bolt will let go next, a course self drilling screw will let go third and a through-bolt won't let go at all.

I know what my choice would be.

BTW, if it's a light-usage fitting in reasonably thin GRP, the better fastener IMO would be a pop rivet of suitable size, as long as the end of the rivet goes all the way out the other side of the skin.

But still, a doubler plate on the other side would be my choice.
01-31-2009 03:05 PM
AllThumbs My thoughts is sheet metal screw unless the fiberglass is quite thick, If it's thicker than the diameter of the screw I might be inclined to vote for the tapped bolt.

Eric
01-31-2009 02:17 PM
sailingdog Fiberglass is too brittle to take screws well. If the screws get highly loaded, the threads of the screw will just tear through the fiberglass.
01-31-2009 02:13 PM
newpbs The question does not seem to be worth a lot of thought, IMHO. If you are concerned about the holding power of a particular fastener use a backing plate and through bolt the assembly.

I would always choose a tapped hole in steel over a self threaded hole.

Paul
01-31-2009 02:04 PM
tommays Maybe

BUT NOTHING holds anything all that strong in glass which is why most stuff gets through bolted
01-31-2009 01:31 PM
kaluvic Me too...but the difference my be in the number of threads..the bolt may have more.
I still think the screew wins.
01-31-2009 03:45 AM
trantor12020 pilot drilled sheet metal screw has large & deeper thread to bite into the fiberglass so my money is on sheet metal screw.
This thread has more than 10 replies. Click here to review the whole thread.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 12:49 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.