SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Boat Builders Row > Ericson > Ericson 35-3 hull to keel joint
 Not a Member? 


Thread: Ericson 35-3 hull to keel joint Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
06-13-2010 03:10 PM
sailingdeac My 87 E34 has a similar fine opening. Bolts would not tighten further. I think the comment on the forward placement of the bolts is valid. So I very much doubt this is a problem
01-09-2007 01:07 PM
FrankLanger For sure any possibility of a hard grounding needs to be checked carefully, and repaired properly. But aside from that possibility, so many boats seem to have issues with the keel/hull joint (e.g. the C&C "smile"), that this issue merits further exploration. The Ericson website had a post showing pictures of keel bolts that had corroded badly--developed a significant "waist" to about half their thickness. With the cost of dropping and rebedding the keel, many owners will ignore this possibility. While one rarely hears of boats losing their keels while underway, I am guessing there must be quite a few older boats with questionable keelbolts.

So far, I haven't heard of any good way of determining keelbolt condition, or good indications of a potential problem, other than x-ray (not possible with a lead keel) or proactively dropping/rebedding the keel. I have wondered at times if it wouldn't make sense, and maybe be cost-effective, to simply add 2 - 3 new keel bolts on any 20 year old boat; I guess the key question here would be where to add these new bolts from a structural point of view, to be able to take the stress and provide good support if needed. Any further comments welcome....
Frank.
01-08-2007 08:42 PM
CaptDaveB
not necessarily

Bill Z & Frank

My line of thought on this matter:

The trailing edge of the keel tapers and is very narrow. I think the caulking washes out over time. The keel studs are located further forward and the caulking there remains intact, thus sealing the bolts. If the keel stud nuts are tight and water is leaking into the bilge, there is a problem.

Perhaps some other owners might speak up regarding this. There is no way to know to know for sure unless you were to haul the boat, drop and rebed the keel. I took the gamble, but I also got a good deal on my boat.

One thing I would look for is stress cracks in the fiberglass near the aft part of the keel to hull joint, inside and out, indicating a hard grounding. Particularly if you have the deep draft model.

Dave
01-08-2007 03:18 PM
FrankLanger Would you not be concerned about the possibility of seawater getting at the keel bolts and causing corrosion over time?
Frank
01-06-2007 12:28 AM
CaptDaveB My 35-3 has the same small gap on the trailing edge. I tightened the keel bolt nuts; still a small gap. I don't think it is a problem if the rest of the keel is flush with the hull and the nuts are tight.
06-30-2006 12:06 AM
egregerson
gap

Have it surveyed; or other 'expert' opinion/advice. An ounce of caution....
06-22-2006 01:31 PM
Bill Z
Ericson 35-3 hull to keel joint

I'm looking to purchase a 1988 35-3. The boat is in very good condition except i noticed a gap on the trailing edge of the keel to hull joint. I can see light between the two and it extends about 5 inches in from the trailing edge.
Any thoughts???

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 03:38 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.