SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Drilling Hole in Fiberglass Hull
 Not a Member? 


Thread: Drilling Hole in Fiberglass Hull Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
03-17-2011 10:37 AM
Liquorice To make a hole bigger with a hole saw, you use 2 hole saws.
1 the same size as the old hole, 1 the size of the new hole.
Nest them together on the same arbour ( some arbours won't take 2 hole saws, but most will. Harbor Freight sells one that's a little longer)
Use the smaller hole saw as the guide - real easy.
03-15-2011 07:00 PM
ereiss Thanks, just ordered my dremel. Certain that it will be a very handy tool to have. Thank you all for the advice.
03-15-2011 06:58 PM
mitiempo My Dremel sees a lot of use. A sanding drum on a Dremel flexdrive and a vacuum in the other hand to catch the debris makes the job not much longer than the time it took to write this.
03-15-2011 02:23 PM
eherlihy I suspect that the ˝" hole prevents you from using the center drill in the hole saw as a guide. Here is what I have done;
  • Use the 1" saw to cut a hole in a piece of ˝" plywood.
  • Then take the piece of plywood (with the hole) and fasten it so that the 1" hole in the plywood is over the ˝" hole in the hull (use clamps, and/or a helper).
  • Use the plywood as a guide for the hole saw.. Simply place the 1" hole saw in the hole in the plywood, and run it in reverse to cut through the gelcoat, then forward to finish off the hole through the hull.

Take care and good luck!
03-15-2011 01:26 PM
tommays If the hull is not to thick you would be amazed what you can do with a pencil and a dremel with a good bit


you can also glue a plug into the hole and then holesaw to the new size
03-15-2011 12:45 PM
ereiss
Drilling Fiberglass (hope I'm not dredging up a too old thread)

I need to enlarge the hole that my head vent goes through (vent tube is only 1/2 inch and need to go to 1"). So, obviously well above the water line.

1. Any secrets on how to "redrill" the existing small hole to the proper size?
2. Is there a best type or brand of hole saw? I bought a set from Harbor Freight and I guess they are worth what I paid for them (not much). I would think a fine toothed hole saw would be best.
3. A real "duh" I certainly believe one drills from the outside in. right?

As always,thank you for your help.
08-29-2010 09:01 PM
mitiempo Hole drilling is pretty straight forward. If I am using a dremel to prepare the core for epoxy I use a vacuum held in the other hand and there is little or no stray dust.
08-29-2010 08:53 PM
sailingdog Really don't need a tyvek suit for this job... a full face mask respirator is probably a good idea and far more protective and comfortable than a half-mask and goggles.
08-29-2010 04:52 PM
mitiempo The hole should be the size required for the through hull. If the area is cored you want to cut the core back a bit and replace it with thickened epoxy, leaving the inner and outer skin intact.


A face mask yes, but a tyvek suit to drill a hole?
08-29-2010 04:30 PM
bluwateronly I don't think you want the hole in the getcoat larger than the size of the thruhull. If the area is cored and not pure glass then you want to prepare it, think dremmel tool here, their are so many threads you can learn from here, really, that can say it much beter than I.Backing plates are easy to make since you have the epoxy and some fiberglass.I would use 4200 when installing thruhull, uv. Take care and the hardest part is drilling the hole!
This thread has more than 10 replies. Click here to review the whole thread.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 04:26 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.