|Topic Review (Newest First)|
|02-21-2011 11:48 AM|
|sailingcal21||Congratulations. That's good info to know.|
|02-21-2011 11:10 AM|
Well, I join in the chorus that I would replace the tank. If anyone is interested, I posted back in October about my tank in an 1983 O'day 34. Being the anal engineer I am, I did some calculating and I contacted the Florida Marine Tank for original drawings. I calculated that if I lowered the over all height of the tank by 3" I would not have to cut any fiberglass and it would reduce the tank from 30 gal to 24 gal - which was acceptable to me.
Well it worked as I installed this weekend. My old tank had 3 weep holes that caused the problem in the forward bottom lip. Since the fuel had gotten into the wood cradle, I removed the entire wooden cradle and replaced. If anyone does this, just be careful to remove the four wooden cradle sides intact so you can use them as a pattern. Also, the foward panel, you will need to lower the lip by 1 1/2" so the tank will slip into place as the tank top will come in contact with the steering pulleys. By lowering the lip, the tank slipped in like a champ. This kept me from having to remove another parts and I had the tank completely in and engine running in about 10 hours with out removing anything or cutting anything except pullng out the batteries.
|02-17-2011 12:38 AM|
Fab pictures, not sure about the intelligence test tho I could see 74. Bit high for me.
Cleaning the diesel tank every few years is a worthwhile job. I just let it run low and suck everything out.
Adding diesel conditioner helps the tank and engin and always fill using a filter, not direct from the pump.
|02-16-2011 07:03 PM|
|deniseO30||Nice choice Colin! same as my boat. replace tank. can almost bet you need to anyway. here's a slide show of my boat with ash I used for table and icebox tops.|
|02-16-2011 06:41 PM|
I have looked over your posts. It looks like I will be the proud owner of a 1983 30 o'day next week. It is located in Michigan, I am in Canada. I hope I don't have too many problems but it has sat for 3 years! 16 Hp universal diesel.
|02-13-2011 08:41 AM|
Tip for a leaky deisel tank.
Rub the leak with hard soap, carbolic works well on a seam leak .
Get you home safe, just don,t forget to fix it.
|02-13-2011 07:19 AM|
While you have the engine out, you may as well do it. If you are paying to have the work done, it might cost you another $150 in labor to remove and reinstall the tank. Compared to R&R of the engine, this is trivial.
I agree with HS, it will assuredly have a pile of crap at the bottom.
Good luck, and post pix!
|02-12-2011 05:56 PM|
Pulling a tank is easy when there's a big empty space in front of it.<G>
And there's pretty much guaranteed a load of crap in it, easy to clean out when the tank is out in the open.
I'd say go for it.
|02-12-2011 05:39 PM|
|rustyballast||I am pulling my engine on my O'Day 30. I wonder if I should pull the fuel tank at the same time and inspect / replace as it seems to fill the entire cavity behind where the shaft goes through the hull. It appears to be more than a 20 gallon tank. I purchased the boat two years ago and the tank was full. I have yet to add any fuel to the tank and it still indicates half full. I have added the starbrite diesel treatment to it. Hmmm.... they say diesels will run on peanut oil :-)|
|11-14-2010 02:33 PM|
Again, the tank is not leaking yet, but I am hoping to avoid a messy and expensive repair when I can least afford it.
HS - your post gives me an idea. Yes, I can go without the tank for a couple of months, as she has been hauled for winter. Unfortunately, the tank is currently FULL. (30 gallons of diesel at $3.50 a gallon is 100 bucks worth of fuel). The idea is to run the tank down over next season, and to simply paint the bottom and sides when I have the opportunity.
SC21 has a picture of his tank unmounted, but still trapped in the engine bay (before he unleashed the jigsaw).
I'll bet that I can access the bottom of the tank if I disconnect the fuel lines, remove the battery boxes, and move the exhaust out of the way.
If I do have to remove the tank, I will cut the aluminum tank and not the fiberglass.
|This thread has more than 10 replies. Click here to review the whole thread.|