SailNet Community - Reply to Topic
Thread: Sealing the gap - top loading freezer Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
06-22-2011 03:56 PM
arf145 Looking at the picture, I think jrd22 has the right idea--put the gasket between the side of the upper insulation and the side of the fridge, rather than under the lip of the lid. There appears to be a gap there, and you'll get your seal without interfering with the lid closing.
06-22-2011 03:35 PM
Originally Posted by CalebD View Post
2 words: Butyl tape.
That would work perfectly for establishing a good gasket. But the stuff never dries, so it would always be there, sticky and catching crumbs from the top surface.

I think silicone would work because it does solidify after awhile. Thinking about this some more, I could tape-off a section of the lid, so the silicone would be exactly where I want it to be. Then I could trim off the excess.


Related to this, I've designed a simple circuit to increase efficiency. When you start the engine (or your wind genny goes into dump load mode), it does a couple things. #1) It affects/restarts the thermostat to override the hystersis between the minimum and maximum temperature. And #2) it puts the compressor on high speed. [And adding #3: it doesn't overdo it when the dump load is frequently cycling on and off.] All that with just a handful of parts and some wire, and it doesn't use any power when standing-by. I've shelved building it until I get a good lid gasket made.

06-22-2011 12:12 PM
CalebD 2 words: Butyl tape.
06-22-2011 10:41 AM
jrd22 I think I would try installing a seal around the top edge of inside of the freezer compartment. It looks like you have a fairly uniform gap between the side walls and the inside of the lid. You could use a high quality neoprene type weather stripping (not the foam kind) that is like a tube with a hollow space in the middle (it comes in various thicknesses). 3M makes a very strong weather strip adhesive that you could use to glue it to the side walls with.
06-22-2011 09:38 AM
bubb2 MD Building Products 1/2 in. x 120 in. Marine and Automotive Weather Strip - 06577 at The Home Depot
06-22-2011 09:25 AM
SVCarolena We have the same problem, so am curious to hear what others may have for ideas. We want to seal the gap not so much to prevent frost (that will happen anytime you open the refer on a humid day), but to increas efficiency. After a humid night, we find condensation on the cold counter around the lid. One unrelated thing we do to increase efficiency it to use a piece of Reflectix insulation cut to fit the top of the box. We use it like a blanket over the contents of the refer. The difference in cycling is amazing compared to without the blanket. Anyway, very interested to hear of possible solutions to sealing the lid.
06-21-2011 01:30 PM
Sealing the gap - top loading freezer

Does anyone have any hints on improving the seal on a top loading fridge and freezer? The gap is too small for the standard hardware store rubber gaskets, and our holding plate quickly becomes covered in frost. (In our nearly empty freezer.)

I tried the very thinnest rubber strip from the hardware store, but it made the lid stick up. I'd estimate the gap to vary between 1/3 centimeter to 1/10th centimeter. The fact that it varies is a part of the problem.

I'm thinking about spraying the edge of the freezer with Pam, smearing grease or other non-stick and then applying a generous amount of silicone to the lid. Then I could wait until the silicone sets a bit and close the lid. Then I'd trim off any excess.

Does this sound workable? There has got to be a better way.


Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome