SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  

Quick Menu
Boat Reviews  
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Hatches and Portlights
Interior And Galley
Marine Electronics
Other Items
Plumbing and Pumps
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here

Go Back   SailNet Community > On Board > Gear & Maintenance > Helm removal
 Not a Member? 

Thread: Helm removal Reply to Thread

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

Topic Review (Newest First)
08-13-2006 05:23 PM
sailingdog Anhydrous lanolin is very viscous, sticky stuff. Lanocote is the commercial version that has some additives to give it better protective properties, but neither is likely to wash away, especially in a very tight area, like the keyway on a steering pedestal.

While I don't know if it would last 10 years, a decade is an awfully long time to go without disassembling and inspecting a piece of gear, especially one as important as the steering system on a boat. But YMMV... if you are willing to risk your steering system failing in a storm, be my guest.
08-13-2006 05:04 PM
hellosailor Lanolin will last for ten years in an exterior fitting, the way NeverSeize will?
08-12-2006 11:40 PM
sailingdog You can use anhydrous lanolin, available at most pharmacies, or Lanocote, available at most marine chandleries, for an antiseize compound, and it's relatively inexpensive.
08-12-2006 07:27 PM
hellosailor If there was corrosion holding your wheel tight, you might want to clean out the hub & keyway, and than reassemble with antiseize. The stuff is expensive, but everyone I know who has started using it, has become a convert.
08-12-2006 07:13 PM
bsfree I (finally) saw the keyway at the rear of the hub last night, all became clear and I used a puller today and off it came. Thanks for the advice guys.
08-11-2006 07:03 PM
We have a YS pedestal as well

but our wheel slides off easily as the rear (or forward facing) face of the wheel hub has the keyway cut in it. I hate to ask the question but are you sure that your wheel hub does not have the keyway cut all the way through so that you can pull the wheel off leaving the keyway in the shaft?

Ours was hard to remove the first time and I thought we had the same problem. A little WD40 and elbow grease got it off for us. If your set up is different then maybe a very small drill bit and screw extractor might get the key out?

Good luck
08-11-2006 03:34 PM
chuckg The best thing you can do is to get rid of the old Yacht Specialties pedestal. They have been out of business for 18 years and new parts are nearly nonexistant
08-11-2006 11:45 AM
Helm removal

Hoping someone knows the right technique to remove a Yacht Services Co helm on my Challenger 32. It looks just like an Edson setup. There is a notch in the hub and I can see a key recessed about 1/2" back. Problem is the rear of the hub is solid and I can see no way for the wheel to come forward without the rear contacting the key, and there isn't a channel from the key to the front of the spline to allow key removal first.
Any advice would be appreciated.

Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

All times are GMT -4. The time now is 12:33 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) LLC 2000-2012

The store is owned and operated by a company independent of the forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.