SailNet Community - Reply to Topic
Thread: Stuck floor hatch PSC 34 Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
07-01-2011 10:17 AM
okapi3 I have had and solved this problem. It is due to humidity swelling the boards. For a while, I removed the stuck boards using a sail tie, in a loop, with a carabiner attached. I put the carabiner on the finger pull of the floor board and the sail tie around my hips and then by squatting and doing a quick leg press, popped the board out.

Finally, I used a hand plane and planed the edges down and then sealed them with epoxy and the boards no longer stick.
06-30-2011 07:27 AM
Cruisingdad You already got it out, so this info may not be for you, but for anyone else with a stuck floor board:

First, try closing up the boat if you have time and put in a dehumidifier and let her run. It may reduce the moisture content enough to manually pull out without scarring the floor. Also, check your rigging. If you have recently tuned the shrouds, you may have flexed the hull to the point you have pinched the boards. Had this happen on a Tayana, Tartan, and a few other boats.

06-29-2011 08:33 PM
steneck RainDog - The pry bar worked. Thanks for the tip.

06-28-2011 08:52 PM
Roger that

Thanks RainDog,

I have one of those at home and will give it a try. Looks like the wide edge will be less likely to ding than a screw driver.

06-28-2011 09:19 AM
Originally Posted by steneck View Post
RainDog - I'm wondering where you drive the shim. It is least tight for and aft but I still do not have a gap. I played with a screw driver but saw that was going to become a ding and I quit.
I used something similar to this: Craftsman 13-1/2 in. Pry Bar Reviews - Craftsman Community and force it between the two boards. The goal is just to push them apart so there is a small gap between the two floor boards.

After I am done with this, I stick a 2 foot screwdriver through the finger hold and use it as a lever to lift the board.
06-27-2011 05:04 PM
steneck HI Folks,

Thanks for those suggestions. I did try to run my knife along the edge but maybe a razor blade is a better tool. But as they say in Maine, "it's tighter than bark to a tree.

RainDog - I'm wondering where you drive the shim. It is least tight for and aft but I still do not have a gap. I played with a screw driver but saw that was going to become a ding and I quit.

I do have a wood toggle that I used as a lever but without success. The wood bowed but did not pop out.

Have any of you ever considered using a penetrating oil to loosen the stuck edges? Or will that make it worse? If I ever get this unstuck, I will sand them for this summer and then sand and varnish them for next year.

06-27-2011 03:26 PM
hellosailor Bob, if those tricks don't lift it clear, you can take a wood toggle on a bit of line (like you'd see buttoning a classic stadium jacket), push the toggle through the hole, and then put your back into lifting on that line.

It almost always is a problem of the wood getting damp and expanding, and if you sand it down a little magically the opposite happens and the board never stays put again.

Floor boards really need to be sealed on all six sides (top, bottom, and the edges) or they'll find a way to change size on you. Or, you install them a little loose and use slides or pulls that can secure them down.
06-27-2011 10:53 AM
RainDog I had the same problem and decided the problem was they were two close to each other. I forced a shim between the two boards to push them away from each other. Then used a lever to pull one up. After I had them up a cleaned all the joints really well and now they come up pretty easy. If you have a dehumidifier or AC, run it for a week before you try to reduce the swelling of the wood. This will make your life much easier.
06-27-2011 08:52 AM
Norstar Bob, Try carefully using a razor knife to cut the joint around the hatch. Maybe someone varnished the cabin sole as in my case and varnish is stuck in the joint?
John S
PSC 34 # 201
06-26-2011 08:18 PM
Stuck floor hatch PSC 34

Hi folks,

I spent more than an hour today trying to lift the floor hatch in the main salon of our 34' Pacific Seacraft. It is under our table and has two finger holds. The aft one is round (without a latch) and the forward one is rectangular and rotates to unlatch (I think).

I suspect my problem is simple swelling of the wood binds the sides of the hatch. However, I used leavers, brute force and even a line that I twisted to create vertical pull without success.

Have any of you had such stuck wooden hatches? Is there a solution to this problem (literally or figuratively)?

Bob Steneck
PSC 34' "Alaria"
Christmas Cove, Maine

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

For the best viewing experience please update your browser to Google Chrome