SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  

Quick Menu
Boat Reviews  
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Hatches and Portlights
Interior And Galley
Marine Electronics
Other Items
Plumbing and Pumps
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here

Go Back   SailNet Community > Boat Builders Row > Alberg > Alberg 37 Chainplates
 Not a Member? 

Thread: Alberg 37 Chainplates Reply to Thread

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

Topic Review (Newest First)
03-24-2012 09:56 PM
Re: Alberg 37 Chainplates

There is an active a37 group and website. There is surprisingly little information on chainplates anywhere though. I definitely want to have a look at the bow plate but it surveyed OK. The tangs and sheaves on the mast head were all OK and are less than 10 years old as is the wire stays/shrouds. Chainplates are original. Thanks for all your help.
03-24-2012 07:31 AM
Re: Alberg 37 Chainplates

Yes, the tabbing does come away in places. I still have to redo a couple of spots. I don't have an old chainplate here at home to measure. Actually, used them for backing plates with the new chainplates. Next time I'm over at boat will measure one although I'd suspect the length could be different on the 37. Did you check the A37 websites? I think there is still an active owner's site.

I also replaced the masthead and bow plate pieces and the wire/ends. The wire and swages all looked good but it all could well have been 40 years old. The bow plate showed the most significant crevice corrosion of any of the plates, maybe because of the welds. It's a challenging piece to fabricate because of all the bends and the front being beveled into the glass. The masthead fitting can be beefed up a little bit without adding much weight.
03-23-2012 09:38 PM
Re: Alberg 37 Chainplates

I have been told the A35 chainplates are the same as the 37. They do look like 1 1/2 x 1/4 in the pictures so that matches. Do you know the length?

My surveyor did spend a lot of time examining the bulkheads and all is well except for a couple small places in the tabbing which is apparently pretty common on these older boats.

Thanks for your feedback.
03-23-2012 07:09 PM
Re: Alberg 37 Chainplates

My A35 had 1 1/2 X 1/4 chainplates. I moved the shroud plates outboard and beefed up to 2" because of the leakage which eventually gets into the deck core and down into the bulkheads from the thru-deck configuration. It may be worth a look-see (if you have not already done so) to determine if there is any leak damage to bulkheads or deck core rot. Replacing the bulkhead(s) is a big job.
03-20-2012 07:27 PM
Alberg 37 Chainplates

Just bought an A37 great condition but chainplates are original and one is showing signs of fatigue. Boat is in MA and I am in Annapolis. Anybody have pictures or dimensional drawings of the chainplates out there - Mark II version. I believe they are all straight bars. Just trying to save a trip or two up there before launch.

Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

All times are GMT -4. The time now is 11:59 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) LLC 2000-2012

The store is owned and operated by a company independent of the forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.