SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Need help with rolling and tipping
 Not a Member? 


Thread: Need help with rolling and tipping Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
06-08-2013 10:35 PM
oysterman23
Re: Need help with rolling and tipping

Well might as well jump in here...Im doing the same job on decks cockpit and cabin with System Three Ws LPU which is a water based poly finish. It likes humidity but not wind or high temps. I wont even try it over 80 or if the surface has been cooking in the sun for most of the day. Strictly mornings or overcast days. The suggestions on thinning are right on but watch how you wet the tipping brush....pure thinner or pure water principle and effects the same...dilution is the idea but not too much or you have a problem again.
doesnt hurt to have a small bit thinned in a covered container for the tipping brush and to remind you of the approx "viscosity" or your working liquid prior to any exposure. Petro or water both are remarkably volatile in these conditions of wind or heat.

Anyway mines beginning to look good at 10 ft...just wet sanded with 320 for the next campaign!!! Good luck all!
06-08-2013 09:26 PM
smurphny
Re: Need help with rolling and tipping

Quote:
Originally Posted by Barquito View Post
I have been having trouble with my two part paint, too. I'm using Interlux Perfection. I think my trouble is that on the days that I have had to paint there has been too much wind. I can't build a cover over the boat in my boat yard. My solution is going to be to lower my expectations. These modern paints are optical illusions. A few people in the yard have been blown away by what an awesome paint job I have until they get a closer look. The shine makes you think it is perfect until proven otherwise... That is my theory, and I am sticking with it.
If it's any consolation, I have not been able to get Perfection to lose brush marks although I've tried a few times. It's always disappointing when waiting for brush marks to flatten and it doesn't happen. Must be doing something wrong or not using the right thinner. It seems difficult to work with.
06-07-2013 04:19 PM
misfits
Re: Need help with rolling and tipping

Quote:
Originally Posted by kjzerr View Post
I would gladly assist you with your boat when you get around to refinishing it.


Thank you!
06-07-2013 12:02 AM
seafrontiersman
Re: Need help with rolling and tipping

I painted my hull with petit easypoxy and had GREAT result. The key was the between coat sanding. Did 5 coats and sanded between coats with progressively finer sand paper and between the 4th and 5th coat I used a scotchbrite pad. I'm probably telling you something you already know....
06-06-2013 04:38 PM
kjzerr
Re: Need help with rolling and tipping

Thanks for the offer, Bob. My wife has been helping, and we put the final coats on over the past couple of days. It came out acceptable, but not what I expected. Of course, my expectations are very high. In the water it will look great, I believe.

I would gladly assist you with your boat when you get around to refinishing it. My schedule is very flexible. Just drop me a line.

K

p.s. Thanks again to everyone who responded. Each one of you had something valuable to offer. I am always amazed at the response on this forum and the quality of the information. As a newbie, this forum has been a valuable tool to help me get started with sailboat ownership.
06-02-2013 09:28 AM
tommays
Re: Need help with rolling and tipping

It really does not matter that much what you tip the paint with as the most important thing tipping does is pop air bubbles from the roller

The roller really DOES matter as its job is to lay down and even film of paint and understanding how much paint you can load on it and how far that goes is the KEY

You must tip ONE TIME AND FAST then you must leave it alone to do its thing and roll the next section ASAP before you lose the window to tip the joint between sections

AS TAQ explained the paint viscosity and the drying time the thinner provides must be at the point the paint can self level
06-02-2013 09:22 AM
misfits
Re: Need help with rolling and tipping

KJZ,

It takes 2 people to roll & tip so if you're trying to do this alone....
If you need an extra hand send me an email, we're practically neighbors. I'll be painting my boat this year so maybe we can help each other out.

Bob
06-02-2013 08:32 AM
i_amcdn
Re: Need help with rolling and tipping

Use a quality foam brush from Lowes. Do not cheap out on the foam. I switched to foam for my second coat and the finish was much better. This fall I will sand out the remaining brush strokes and re-do with only foam.
06-01-2013 11:40 PM
TQA
Re: Need help with rolling and tipping

Quote:
Originally Posted by kjzerr View Post
Hello all:

I am repainting my boat by rolling and tipping. I am using Petit EZpoxy2 two-part epoxy finish. I'm having trouble getting the finish to flatten out. Also, the areas where the tipping overlaps is visible after the finish dries.

The past couple of days the temps have been 85-90 degrees with low humidity. Petit recommends 50-90 degrees for application, so it seems all is in order. I've been adding 8oz of Petit brushing thinner to 32oz of finish. I tipped the first coat with a badger hair brush and the second with a foam brush. Both left visible brush marks. I sanded down the first coat to remove the marks, switched to the foam brush, and ended with the same look.

Should I be thinning it more? Should I not thin at all? Any thoughts would be helpful. Tomorrow's supposed to be a few degrees cooler. Could the temp be the issue?

I have attached a couple of pics. You can see that the shine is good. The one of the transom shows the reflection of the rudder, but notice the brush marks at the right side of the transom. The other is my reflection. All would be fine if I was looking for some abstract artist look, but that's not what I'm going for. ;-)

Again, any assistance would be greatly appreciated.
Get a piece of glass and set it at about 70 degree from the vertical. Roll and tip and see if the brush strokes disappear, if not add more thinner, if it sags and runs add more paint.

Wipe the paint off the glass with thinners let it flash off and try again. This worked for me with International 2 pack and the finish was near a perfect spray job.
06-01-2013 11:08 PM
bljones
Re: Need help with rolling and tipping

Apoparently Mr. Oman needs to spend more money on better searchbots, since Mr. "Too cheap to buy an ad or do R&D," the cheap epoxy king, is replying to a PAINT post.
This thread has more than 10 replies. Click here to review the whole thread.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 12:01 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.