SailNet Community - Reply to Topic
Thread: Throttle control cable Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.


User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
06-21-2013 08:21 AM
patrscoe
Re: Throttle control cable

I had the same problem early last year. As recommended, I installed a Morse Teleflex throttle cable brake. It is a little on the pricey side for what it is ($22). Also I realize that the set screw within the Edson pedestal broke off and was not working right. This set screw also does the same thing. I tapped a new bolt and together with the cable brake clamp, works very well. I have heard of people reworking the internal throttle spring (Yanmar). This is something you want to avoid. If your throttle cable broke, there would be no safety measure of bringing the engine back to idle.

I like Faster's idea on using a larger hose and hose clamp, as long as the hose clamp is strong enough. When you tighten the throttle cable brake, you can hear and see it really compressing within the shield of the cable at one pin point location. With the hose clamp concept, you would have two locations and you would have the hose to soften the load onto the clamp.
But as with the other bolts you would be using, either throttle brake or set screws, you will want to use Loctite on the threads. Not the strong level sealant.

Anyways, easy fix and a couple of options.
good luck.
06-17-2013 02:42 PM
rikhall
Re: Throttle control cable

Here is a cable clamp in use - worked very well.



Rik
06-16-2013 08:37 PM
T37Chef I see cable clamps used often, I have two on my new throttle cable
06-16-2013 03:37 PM
Faster
Re: Throttle control cable

At one end of the cable, cut and slit a piece rubber hose that just fits over the fixed part of the sheath, and overlaps the sliding part. Tightly clamp it to the sheath with a tiny hose clamp, put another over the sliding end and add just enough friction to stop the creep.
06-16-2013 03:29 PM
flyingwelshman
Throttle control cable

I just replaced my throttle control cable - this after an interesting landing in which my throttle came loose in my hands as I was about to turn off the fairway and into my dock. The old cable had seized and the screw attaching the throttle handle sheared. Thank Vice GripsŪ for a quick and effective solution!

Anyway, my new control cable runs too smoothly (from one extreme to another). It doesn't 'stick' at a setting. When released the throttle backs off to just above idle.

Are there any suggestions as to how to increase the resistance in the cable? I was told that this will happen over time and, for the time being tie off the throttle at the desire setting with a bungee etc. I can see this working, but I was hoping for a more permanent solution.

Thanks in advance.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

 
For the best viewing experience please update your browser to Google Chrome