SailNet Community - Reply to Topic
Thread: Xantrex Link 2000 Troubleshooting Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
06-19-2013 10:27 PM
Re: Xantrex Link 2000 Troubleshooting

Just curious, did you try a reset prior to this advice? I tried a reset that lasted about 2 minutes and it didn't work. I'll try the half hour reset. It would be really nice to have both batteries monitored again instead of just one.
06-19-2013 02:37 PM
T37Chef excellent
06-19-2013 10:02 AM
Re: Xantrex Link 2000 Troubleshooting

The hard reset worked. No blinking errors!
06-15-2013 07:56 AM
Re: Xantrex Link 2000 Troubleshooting

Thanks everyone. I also received a response from Xantrex customer service.

They suggested I try a hard reset of the Link 2000 by disconnecting all power and letting it sit for half an hour. I will give this a try before pulling the wiring apart.
06-12-2013 11:53 PM
Re: Xantrex Link 2000 Troubleshooting

I had the same exact problem a couple months ago. I traced the problem from the battery, through the fuse, to the first circuit board, where I followed the voltage through the little paths on the circuit board and then to the display unit where I got in over my head. I found an outfit that repairs these units, but I didn't really want to pull out the monitor, as it also runs my alternator and my battery charger.

I ended up disconnecting the sensor wire to the starting battery and switched the software to just monitor the house battery so the error message wouldn't continue to flash. It's not fixed, but it doesn't bother me anymore
06-12-2013 10:43 PM
Re: Xantrex Link 2000 Troubleshooting

Check the wires going into the back of the display unit as well. Very small connection points here. Maybe a few are a bit loose?
06-12-2013 10:10 PM
Re: Xantrex Link 2000 Troubleshooting

I don't have my manual at home but here are some thoughts...
check the voltage at the battery
check the shunt to the link, if there is any corrosion or lose wire, therefore only sensing the negative load on one side.

I.sent mine back a few years ago to have it serviced for I think $300.
06-12-2013 05:25 PM
Xantrex Link 2000 Troubleshooting

This last weekend an E13 error came up on my Xantrex Link 2000. I looked in the manual and it said “Battery #2 voltage sense leads open”. So I checked the violet wire connections to the start battery (my #2) and replaced the 2A fuse. It was all fine until I turned a small load on and then the E13 error came up again.

I then disconnected the blue wire fuse (battery #1 or house batteries) and as expected E12 came up. Even when I reconnected the blue wire fuse the E12 error continued. It wasn’t until I pulled the fuse on the start battery that E12 was replaced by E13.

So I have replaced both fuses (although the old ones looked OK and the Link 2000 was still showing the voltage from battery #1 and #2). I still have an E12 or E13 error depending on which fuse I last disconnected. I have a Heart Freedom inverter/charger connected to the batteries and the Link 2000 controlling it.

Any ideas as to what to look at next?

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome