SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Using brush instead of spray for gel
 Not a Member? 


Thread: Using brush instead of spray for gel Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
06-23-2013 08:03 PM
PorFin
Re: Using brush instead of spray for gel

Just be careful with the glue/acid brush -- they shed bristles very, very easily. Nothing worse than trying to dig bristles out of wet paint/gelcoat.

A foam brush will work, but I really prefer the control you get with a real bristled brush. If you're willing to part with a couple of bucks, grab an artist's brush at Michael's or some other hobby store.

I never found waxed gelcoat a problem on it's own, but given a choice I'd go with unwaxed. You can air inhibit it with PVA or plastic, or if you know you're going to be building up a couple of coats you can just let it set and apply your second coat without having to scrub and sand.
06-23-2013 06:32 PM
lancelot9898
Re: Using brush instead of spray for gel

There is a youtube presentation by TAP Plastics that shows what looks like a disposable glue brush being used to apply gel to a vertical surface. I thought that it would remove a couple of steps from going the preval sprayer route. Plus I would not have to thin with the styrene if I go that route. A small foam brush might also be an option. Apparently the demonstration used a non wax gel in that it showed three ways to get it to cure. One being applying heat via either a hair dryer or sun, two via the standard PVA? spray and thee via a celephane sheet to block the air so that it fully cures. It does not mention the wax gel which does not require any of those steps, but someone suggested that the wax gel is a pain to work with. Also I really don't want to fill in those grouves and I'm just trying to cover the small pimples thinking that a thin coat of gel will hide those flaws.
06-23-2013 04:09 PM
PorFin
Re: Using brush instead of spray for gel

Yes, you can use a brush.

The challenge on vertical surfaces is keeping the gel from running/sagging. If you use a piece of acetate over the top of the repair, you can keep it in check. Tape all the way across the bottom first, apply the gel, then roll the acetate up over the repair. Use a plastic squeegee or body filler spreader to work it relatively flat. Tape the top, then tape the sides. The good thing about the acetate is that it will leave you with a pretty fair surface. The bad thing is that with the molded planking, you're gonna have to reestablish all those grooves.

I've tried to get a Preval sprayer to work with gel, but have had little success. The problem is that the you need to thin the gelcoat considerably to get it to spray well. A couple of suggestions if you decide to go this route:
- Pull the strainer off of the pick-up tube on the sprayer.
- Thin the gel with Styrene only. Acetone will work, but it flashes really quickly.
- Adjust your mix before you add any catalyst. Spray onto a piece of glass, and add styrene until you get a coat that covers smoothly but doesn't sag/run.
- Add the amount of catalyst needed for the volume of the total gel & added styrene in the bottle. If you only add enough catalyst for the gel you started with, then the gel won't dry fast enough.

Good luck which ever method you choose.
06-23-2013 02:24 PM
overbored
Re: Using brush instead of spray for gel

you can use a brush for small touch up and on horizontal surface but on vertical surface no way, it just does noes not work well. if you want to spray on a small area it is best to use a Preval sprayer.
Preval ? Preval Sprayer Products.
these work great for gelcoat and you don't need a compressor
06-23-2013 10:41 AM
lancelot9898
Using brush instead of spray for gel

For covering up some flaws in the hull, has anyone used a brush rather than a spray for applying gelkote? More sanding would be needed, but it should sand down rather easy would be my guess? A picture of the hull that needs work is attached.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 09:38 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.