SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Chat  
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Boat Builders Row > Tartan > Tartan Piper 28 Stuffing Box Maintenance
 Not a Member? 


Thread: Tartan Piper 28 Stuffing Box Maintenance Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
3 Weeks Ago 10:28 AM
jimbob77
Re: Tartan Piper 28 Stuffing Box Maintenance

I've owned the boat a little over a year. I've had to adjust the packing nut three times to keep the drip at a reasonable level. My intent in changing was that I thought the packing was worn down and I wanted to replace it with Goretex packing, which I used on a previous boat and found to be virtually dripless. For now, I am going to keep adjusting . Thanks for your comments.
3 Weeks Ago 07:38 PM
tomh85
Re: Tartan Piper 28 Stuffing Box Maintenance

Why are you changing the packing? if it not dripping excessively leave it alone. The boat designer did a bad job, not leaving enough room to do maintenance. I have 1984 tartan 28 with original flax packing. I observe the temperature and the drips per minute. Turn nut each year as needed. Still sailing.
4 Weeks Ago 08:52 AM
jimbob77
Re: Tartan Piper 28 Stuffing Box Maintenance

I just discovered the same problem on my '87 Tartan 28. What did you end up doing and did you put in a new type seal? Thanks
07-09-2013 09:11 AM
deniseO30
Re: Tartan Piper 28 Stuffing Box Maintenance

Welcome to sailnet! Uh.. cut the shaft? Seems a bit extreme. Is she in or out of the water? Photos? (we all use a web based photo site and post the direct links for photos here)

If the engine to shaft coupling is like most. it's near impossible to remove off the shaft without a purchased or homemade type of bar and bolt "puller" (actually pushes the shaft out)
Some people slide the engine forward. Some won't/can't/abhor the thought of dropping the rudder to get the shaft out and pull the engine! Some say "f" it and cut the shaft!

Oh.. NEVER use a slide hammer to pull the shaft or a hammer to drive the shaft back in! Sure way to damage the transmission.

Anyways... if your going to cut, pull, chop or drop; think new cutless bearing also. and motor mounts... and ... and ...
07-09-2013 08:57 AM
tommyp
Tartan Piper 28 Stuffing Box Maintenance

I'm trying to replace the packing on our '92 Tartan Piper 28 but there's not enough room to pull the nut far back enough to pull out the old and put in the new. In talking to the boatyard and looking online it seems the only option is to cut the shaft and redo everything.

I also found there are some alternative methods when putting it back together using a PSS shaft seal or a split coupling to make access easier in the future.

I'm curious if there are any other Tartan owners that have run into this same issue and what they found worked best.

Thanks!

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 01:09 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.