SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Electronics > How to connect a Standard Horizon GX2100 AIS VHF to a Raymarine RL-70C plotter
 Not a Member? 


Thread: How to connect a Standard Horizon GX2100 AIS VHF to a Raymarine RL-70C plotter Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
07-22-2013 10:35 PM
joevar
Re: How to connect a Standard Horizon GX2100 AIS VHF to a Raymarine RL-70C plotter

I did try adding a third resistor but it yielded the same results.
07-21-2013 01:44 PM
GNU
Re: How to connect a Standard Horizon GX2100 AIS VHF to a Raymarine RL-70C plotter

Joevar,
That's interesting.
I'm guessing it's still related to the original issue (the voltage difference in the signal).
Do you have access to an additional resistor that you can add in series? The common resistors have quite a bit of play in them so you may not have enough. An alternative if you don't have an additional resistor onboard is to add a long and thin cable. That also adds resistance. If that works then just go back to Raidoshack and get a resistor when you have time.
07-21-2013 01:44 PM
joevar
Re: How to connect a Standard Horizon GX2100 AIS VHF to a Raymarine RL-70C plotter

The RL-70 outputs
NMEA Data output on Blue
NMEA ground on White

The Standard Horizon GX-2000
NMEA In + is Blue
NMEA Common - is Green
NMEA Out + is Gray
NMEA HS In + is Brown

I connected RL-70 Blue to Standard Horizon (SH) Blue and maintained that connection.

I then connected RL-70 White to SH Green with and without the resistors. Worked for 10 seconds then stopped

I then disconnected Green and connected RL-70 White to SH Brown with and without the resistors.
Worked for 10 seconds then stopped
07-21-2013 01:19 AM
MarkSF
Re: How to connect a Standard Horizon GX2100 AIS VHF to a Raymarine RL-70C plotter

So how are the grounds connected? As I described and nothing else?
07-20-2013 10:51 PM
joevar
Re: How to connect a Standard Horizon GX2100 AIS VHF to a Raymarine RL-70C plotter

I tried connecting it without the resistor but it does not work.

Tried using either Brown or Green on the radio for the NMEA -, but it only works if I use the resistor, but only for 10 seconds.
07-20-2013 03:09 PM
MarkSF
Re: How to connect a Standard Horizon GX2100 AIS VHF to a Raymarine RL-70C plotter

Personally I have my doubts about the resistors. What happens if you connect it up the simple way?

This would be :

Signal out on RL70C to port 1 RX IN (grey) on the VHF

Signal ground on RL70C to ground (black) on the VHF

That should be all it takes.
07-20-2013 12:48 PM
joevar
Re: How to connect a Standard Horizon GX2100 AIS VHF to a Raymarine RL-70C plotter

So I am having the same problem in connecting my standard horizon gx-2000 radio to my Raymarine RL-70c.

I went to radio shack to buy the resistor. Closest they had was 3.9k ohm 1/2 watt resistors so I took 2 of them and wired them end-to-end and connected them as instructed.

At first, I got a fix on the radio and the satellite icon lit. But 10 seconds later the icon began to flash. Coordinates still display although the SOG and COG go blank. In time it is obvious the the connection is lost because the time does not change.

If I turn the radio on and off, no satellite icon and no fix. If I disconnect the NMEA - and reconnect, same problem. I see a fix for 10 seconds and then the icon flashes and SOG and COG goes blank.

I have tried using one resistor and 3 resistors in series and have the same result.

Any ideas?

Thanks.
01-04-2012 01:30 AM
GNU
How to connect a Standard Horizon GX2100 AIS VHF to a Raymarine RL-70C plotter

I've spent quite some time troubleshooting this issue together with a very helpful chap from Horizon's support department (Devin) and thought I share our findings with RL70 and RL80 owners.

What I wanted to do:
Get an NMEA0183 signal from my RL70's NMEA out port to feed GPS info to the Standard Horizon AIS capable VHF.

What I tried to do:
Connect the NMEA cables to the VHF following the instructions in the VHF manual.

What was the result?
Well not much would be an overstatement. The VHF didn't even indicate a fault signal (it would do that by flashing a graphical representation of a satellite in the upper right corner of the display)

After days of research and troubleshooting it turns out that my plotter had an outdated firmware (2.09) and only supports NMEA0183 version 1.0 (The VHF requires 2.0 or later) This by itself was quite tricky to find out since Raymarine's "support" couldn't tell me what's been updated in later versions (V4.x is the latest version). All they could tell me was that they no longer support memory card updating and I had to disconnect my unit and send it to them for an update that might fix the issue (this would take weeks according to them (sigh))

So, rather than dealing with Raymarine I read up on the difference between NMEA 1.0 and 2.0.
Turns out the differences includes changes to the voltage levels and tge way the signal ground work.
After hours of thinking and testing we found that there were two potential fixes.
1. Buy a Raymarine Raytech NMEA box for $150+tax+shipping.
2. Alter the NMEA output signal levels slightly and disconnect the signal ground.

Summary:
We went with option 2.
Here's what we did:

1. Connect NMEA+ from the plotter to NMEA in (blue cable) on the VHF.
2. Connect NMEA- from the plotter to the NMEA in on the VFH via an 8k Ohm resistor ($1 part at the closest Electronic part store / Radio shack etc).
3. Isolate the NMEA ground (green cable) from the VHF and leave it disconnected.
4. On the "NMEA out" menu option in the RL70, select RMC (you can de-select the other options if you don't have another NMEA consumer.

That's it. Your GX2100 will now be able to read the GPS location from your plotter!

PS. The RL-70 doesn't support an AIS overlay so you'll have to connect the VHF NMEA out to another device (Seaclear on a PC?) if you want that.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 02:56 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.