SailNet Community - Reply to Topic
Thread: Testing Electronics Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.


User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


  Topic Review (Newest First)
08-12-2013 07:47 AM
NS Crew
Re: Testing Electronics

It's a Navman. That's interesting what you mention about the transducer. Thank you all again!
08-08-2013 12:26 PM
Plumbean
Re: Testing Electronics

What kind of unit is it? I know that a Raymarine ST50 can be tested at the junction box to see if the signals are coming through. Basically, if the transducer is hooked up and getting power, it will be varying the voltage on the wires depending upon wind direction and speed.
08-07-2013 06:14 PM
NS Crew
Re: Testing Electronics

Hello!

The display does light up but it doesn't seem to be receiving any information from the indicator. I can clearly see what the display offers but the information is not correct. Furthermore, the wind direction needle stays in one direction and doesn't move. I believe that the speed is also inaccurate. I have tried to recalibrate and other things like this but to no avail.

What I want to try to figure out is if there is a way to test the wiring from the masthead cable junction box to the indicator at the top of the mast. Is there a way to test the electric circuit and the signal wire separately to see if they are functioning properly?

Thanks!
08-07-2013 12:40 AM
davidpm
Re: Testing Electronics

Quote:
Originally Posted by NS Crew View Post
Hello!

I'm not that savy with electronics so I apologize if this is a simple question. Is there a way to test a wind speed/direction indicator at the top of the mast to see if it is working? It used to work and now the display unit in the boat isn't reading anything. So I want to know if it's the display (or the wiring from the display to the mast) or if it is the indicator (or wiring from mast up to indicator) at the top of the mast.

Thanks!
If you can find the specs you might be able to find what signal is coming from the indicator.
Then disconnect the input and generate your own input somehow.

Most likely however the power is not getting to the panel.
I would think that even with the indicator not hooked up at all the panel should light up.
08-06-2013 11:47 PM
mark2gmtrans
Re: Testing Electronics

Check all the connections, if it is totally blank either something is unplugged or the display is a dead ducky. I guess you could send someone up there blow on it....

If you get someone else to do that be sure to take pictures.
08-06-2013 11:38 PM
PaulinVictoria
Re: Testing Electronics

I would think if the mast indicator was FUBAR you'd perhaps see some sort of life on the display, even if it was junk. If it's completely blank then I would suspect the display itself. Look for the obvious stuff first like has the unit got power etc.
08-04-2013 07:40 AM
NS Crew
Testing Electronics

Hello!

I'm not that savy with electronics so I apologize if this is a simple question. Is there a way to test a wind speed/direction indicator at the top of the mast to see if it is working? It used to work and now the display unit in the boat isn't reading anything. So I want to know if it's the display (or the wiring from the display to the mast) or if it is the indicator (or wiring from mast up to indicator) at the top of the mast.

Thanks!

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

 
For the best viewing experience please update your browser to Google Chrome