SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Backstay tension
 Not a Member? 


Thread: Backstay tension Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
08-28-2013 02:58 AM
SchockT
Re: Backstay tension

I have a Navtec hydraulic system as well. For racing purposes you should be able to ease it off so that the forestay is a bit floppy, but nothing like you describe. Last summer when we were out cruising the pump blew a seal and we had no hydraulics. I was able to tighten the backstay turnbuckle that attaches to the ram enough to allow us to sail comfortably in moderate breeze, albeit with more headstay sag than I would like. A couple of times it was breezy enough so that I REALLY wished I had more tension, and we became overpowered much sooner than I am used to. Now that I have rebuilt the pump I am going to keep the minimum tension a bit higher than I used to. I consider around 3000psi to be a pretty good Max, but you definitely want to make sure you don't forget to ease it off when you are done! When it is quiet at the dock and I crank it on I can hear the boat creak and groan a bit!

I never realized how much difference having that adjuster made until I was forced to live without it. I don't think I would ever own a boat without one!

BTW my boat is a masthead rig, and I get plenty of mast bend even without the baby stay on hard. It makes a huge difference to the main as well as the genoa. It certainly DOES make the boat faster because it allows me to make tuning adjustments that just aren't practical if I just had turnbuckles. Let's face it; not many people are going to go grab their wrenches and start cranking the turnbuckle every time the wind picks up! I'll wager most people never touch their backstay once the mast is up! While those people are contemplating putting in a reef, I just reach down, and with a few strokes of the handle and I am good for another 10kts of wind! It's a no-brainer to me!
08-27-2013 07:59 AM
Sailormon6
Re: Backstay tension

An adjustable backstay doesn't make the boat sail any faster or point any higher to windward than it would be capable of sailing without a backstay adjuster. The ability of a boat to sail to windward is limited by it's design. If you didn't have an adjuster, you could get out your tools and adjust your rig more taut, and the boat would point as high as it's design permits. What a backstay adjuster does is, it enables you to change the tuning of the rig very quickly, on the fly, from taut to loose, without getting out your tools. The taut setting enables the boat to go as fast and point as high to windward as it's design permits. The loose setting enables it to sail as fast off the wind and in lighter winds as it's design permits.

If a backstay adjuster is over-tensioned, it can damage the boat structurally. As you have seen, in some cases it is also bad to adjust it too loose. The maximum tension recommended for a boat is generally based on the type and size of the boat's shrouds.
08-26-2013 09:40 PM
JimsCAL
Re: Backstay tension

It is possible to overtension the backstay. I've of race boats that were damaged by over zealous use of the backstay tensioner. Easy to do with a hydraulic unit. Mine has a pressure gauge, and the previous owner put a piece of tape on the piston rod at the maximum tension point.
08-26-2013 06:14 PM
overbored
Re: Backstay tension

the backstay on a masthead rig is to control the headstay sag and the baby stay will give you some mast bend to flatten the mainsail.
08-26-2013 05:42 PM
BarryL
Re: Backstay tension

Hey,

In the C&C 34 I race on, we tension the backstay to take all the sag out of the headstay for upwind work. For downwind, we want it loose, not as loose as you had it, but almost that loose.

Barry
08-26-2013 05:04 PM
hillenme
Backstay tension

My current boat has a navtec hydraulic backstay on a mast head rig, along with with a baby stay that goes about 2/3 up the mast. This is a new thing to me as all my previous experience has been on boats with either split backs or no adjustable backstay at all. That said I've found it to be essential upwind on the race course to pull the baby stay on tight and crank in the back stay, and it's been a lot of fun to play with a new sail control.
However, I had a situation the other day that got me wondering what was too little and what was too much tension on the back stay; while heading downwind on a leisure sail, no spin or anything, I asked a non-sailor friend to ease off the back stay. It didn't occur me to mention that when you turn the knob to ease it, it continues easing until the knob is turned back. About five minutes later the rig was so lose that the forestay turn buckle was bouncing back and forth off the deck on either side of the chainplate. it was so lose that the five shims placed in the mast when it was stepped all fell to the floor inside. I cranked the stay back on until most the sag was gone and everything has been fine, although I can't get the shims back in the mast, I don't imagine that matters much. Basically, I was surprised to see that it can ever get this loose, IMHO, it was dangerously loose. If it's possible to ease to this degree, is it also possible to crank it on way too tight, even to breaking load (for example if I had been as undetailed in my instructions and asked a inexperienced crew member to put crank on the back stay and he just went all the way to the end of the rod.) There is a gauge on the pump that lists tells the load between 1 - 6 kpsi. I've found that half way between one and two the rig is pretty tight with minimal bend in mast, but how much can I go? Can I find some recommended min and max tensions somewhere on the web? Boat is C&C 35-3.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 08:02 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.