SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Main Halyard Replacement
 Not a Member? 


Thread: Main Halyard Replacement Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
07-19-2008 06:24 PM
speciald I Agree. Sew the ends together and cover with flexible electrical or rigging tape.
07-19-2008 03:38 PM
knothead
Quote:
Originally Posted by paulk View Post
If I worry that the duct tape is going to let go 65' up the mast, I sew the two lines together with a sail needle and waxed twine.
The above way is much preferable over the duct tape method. That is unless you have other work for the rigger to do when you hire him to go aloft to fish the new halyard through the mast after the tape comes apart when you get the junction to the mast head and attempt to pull it over the sheave.
Trust me. Butt the ends together and stitch them.
07-19-2008 12:15 AM
sailingdog Idealflaw-

IF you have a wire-to-rope halyard currently and want to replace it with an all rope halyard, you really need to check the masthead sheave, to make sure it is designed to handle rope as well as the masthead exit slot to see if the wire rope has damaged the slot and made it a possible rope chafing hazard. A wire sheave usually has a V-shaped groove, where a rope sheave will have a U-shaped groove.

The new high-tech lines are actually better than wire-to-rope halyards. The dyneema or spectra core lines are stronger than wire with about the same stretch and with less weight aloft.

In the future, you should probably start your own thread, rather than hijacking one, like you did here. I'd also recommend that you read the post in my signature.
07-18-2008 11:52 PM
idealflaw this was a good thread. question - my existing halyard is a cable spliced into a rope. I want to replace it so I can run it back to the cockpit as I usually single-hand.

I'll replace it with a plane-ole-line, no cable or anything like that. am I trading down by doing this or is that cable/rope combo no better or worse than traditional rope?

Let me know your thoughts...
02-15-2007 08:30 PM
firehoser75
Thanks for the Advise

You have all given me some useful ideas on how to accomplish this.
Thanks, it is very much appreciated.

Tom
02-14-2007 07:23 PM
paulk If I worry that the duct tape is going to let go 65' up the mast, I sew the two lines together with a sail needle and waxed twine.
02-14-2007 03:22 PM
Valiente
Quote:
Originally Posted by SailorMitch
Sounds more complicated than it is. Also, I use about a 6-9 inch long piece of duct tape to make sure it all stays together.
You can sleeve the tape in shrink wrap tubing for an even neater job. Just lube the outside of the shrink wrap (or work it by hand so it will conform to the sheave radius) and maintain a steady pull up and around.

This job is a lot easier than losing a halyard shackle up the mast when you are alone with no steps. That can get tricky and involve all sort of Masonic-handshake-type contortions.
02-14-2007 03:05 PM
Brezzin I used this method myself and was shocked at how well it worked

http://www.sailboatowners.com/upload...2378230&fno=17
02-14-2007 03:02 PM
SailorMitch Assuming you have the shackle already spliced on the new halyard -- two basic options on how to proceed. If you are going to trash the old halyard, you can cut off the old shackle to save if you want, and use the old halyard as the messenger line to pull the new one through. I usually butt the two ends together and use duct tape to secure them together -- but tug on the joint really well before you pull it through. So butt the tail end of the new halyard to where you cut off the shackle on the old halyard, secure with a big piece of duct tape, and pull the old halyard up and through until the new one is in place. You can still use the old halyard line for something else in you want if it is in basically good shape.

If you want to keep the old halyard intact, you will need to pull the old halyard out first with a messenger line secured to the tailend of it. I use whatever small stuff I have for a messenger line, but make sure it is strong and flexible -- and long enough! Again, I attach the two together with duct tape, overlapping the small stuff on the old halyard if that thickness will go through the sheave. This time you will pull the old halyard out in the opposite direction from the first method. Once the messenger is in place (and I keep some tension on it to make sure it doesn't jump out of the sheave at the top of the mast) remove the duct tape and the old halyard, and attach the new halyard with duct tape. Pull the messenger line through until the new one is in place, and you're done.

Sounds more complicated than it is. Also, I use about a 6-9 inch long piece of duct tape to make sure it all stays together.
02-14-2007 02:39 PM
captw3 Run a smaller messenger line though on the existing halyard then wire tie and/or tape the halyard and reverse the process. Make sure the messenger line is strong enough to take the pull and make the turns without seperating.
Rick EP
This thread has more than 10 replies. Click here to review the whole thread.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 07:35 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.