SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  

Quick Menu
Boat Reviews  
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Hatches and Portlights
Interior And Galley
Marine Electronics
Other Items
Plumbing and Pumps
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here

Go Back   SailNet Community > On Board > Gear & Maintenance > Bulkhead/genoa screws/chainplate fixes
 Not a Member? 

Thread: Bulkhead/genoa screws/chainplate fixes Reply to Thread

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

Topic Review (Newest First)
02-12-2002 03:24 PM
Bulkhead/genoa screws/chainplate fixes

Thankyou for all of your responses. I''ve done alot of research and talked to some friends. I like to get as much info as possible.
Genoa track: I''ll pull the track, clean out the damaged core, rebed it ( I came up with West Systems, epoxy 105, hardner 205, filler 406) then redrill and seal it up with Life Calk. Same story on the chainplates.
Bulkhead: It''s such a small section I''m thinking I''ll cut out the bad wood and a bit into the good wood. Shape the the new piece (marine grade plywood). I''ll seal it with West System epoxy and then "put the piece in the puzzle". I''ll epoxy the edges prior to fitting then epoxy the whole area with a rollor to hopefully make it one solid piece.

Any further suggestions, go for it.
s/v Barefoot
02-11-2002 08:28 AM
Bulkhead/genoa screws/chainplate fixes

Iagree with rebedding --- use silica gel in all deck fittings.

On your bulkhead ... indeed what caused it? ... (likely leaking gaskets in your heads pump?). But for the repair using a two part epoxy glue will simply allow you to insert a new piece to fill your cut out area and will add not subtract strength. Just enjoy the versatility of epoxy!
02-10-2002 01:46 PM
Bulkhead/genoa screws/chainplate fixes

A few questions. Are they screws or through bolts on the Gen track? What is the evidence of leaks? Same questions on the chainplates.
I would remove both Gen tracks and the chainplates examine for water intrusion at every hole in the deck. Only then would I be comfortable with a low moisture reading.
As far as the bulkhead, remove and repair BUT also find out what is causing the water intrusion and repair it.
Best of luck. JEF
02-09-2002 03:55 AM
Bulkhead/genoa screws/chainplate fixes

Sounds like your genoa track screws need to be rebedded and the chainplates re-gooped as well. For the bulkhead, your best bet will be a good book on boat repairs, possibly Gougeon''s or something similar. A single diagram in a book will be clearer than perhaps 10 postings.
02-08-2002 06:45 PM
Bulkhead/genoa screws/chainplate fixes

I just purchased a 1986 Catalina 27 Tall rig. It surveryed well except for three items, I recieved a good "discount" off the asking price because of these items. I was going to have the Marina do the repairs, but I just found out I''m being furloughed from my Job in March. I guess I''ll have plenty of time to work on it and would like to save the money. I''m very patient and want to good a good/quality job. The three items are"
1: Several genoa track screws are leaking (surveyor says very low moisture on his meter, but they are beginning to leak)

2: Port and Starboard Upper Chainplates are beginning to leak (also very low moisture on his meter)

3: The bulkhead between the head and V-Berth has rot in a section 2 inches high by 18 inches wide (at the floor). He recommended cutting out this section and replacing. How do I bond the new marine plywood to the cutout section.
Thanks for your time
s/v Barefoot

Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

All times are GMT -4. The time now is 07:36 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) LLC 2000-2012

The store is owned and operated by a company independent of the forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.