SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > replacing standing rigging
 Not a Member? 


Thread: replacing standing rigging Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
03-06-2007 02:52 PM
Bump I am going to have my standing rigging and lifelines replaced this spring. I decided to pay a professional to do this for three reasons:
1. I am not particularly talented mechanicly.
2. If I screw up the standing rigging and it lets go in a blow, I am looking at a $10,000.00 repair job to replace a bunch of stuff.
3. If I mess up the lifelines and my wife goes overboard, I am looking at an even more expensive divorce.

I guess it depends on your level of confidence in your skills and your ability to accept the possibility that doing it yourself can cause injury, death or result in spending even more money fixing the things that got broken as a result of your work. If a pro dose it at least you can sue the SOB.
03-05-2007 10:27 PM
Hawkwind I would remove the mast. You will probably need a crane. Any marina should have one. I think the cost is something like $50 to $75 dollars around here.

Without taking the mast down, you will need a bosun's chair ($150 or so) and much more time. Each shroud will have to be removed, measured and replaced separately. You'll also want to inspect everything which will be so much easier to do on the ground. Working at the top of the mast is fine for quick jobs. Being small, I seem to get the job more than most. I enjoy going up for quick jobs but would not want to replace everything. Especially since I'll be the guy at the top of the mast. I'm guessing your mast would be about 40 feet off the deck.

Rig tension can be critical for speed. I've always adjusted my own though and nothing has fallen down yet. I just try to get the shroud tension even, by standing between them and pulling with my fingers. On most sloops, I think the mast is mostly held up by the two outer shrouds, which are anchored slightly behind the mast, and the forestay. The backstay bends the mast for sail shape and I guess the inner shrouds help support the forces on the outer shrouds. I've always started by setting my forestay and adding tension to the outer shrouds til it 'feels' right. Then I tweak the inner shrouds to be something less than the outer shrouds, even tension of course. Then I walk around the boat, look at the mast from very angle, tweak here, adjust there til I'm satisfied.

There are tension gauges that can be bought to remove the guesswork. You can get it all set up and have a local expert check the tension for you. When I say expert, I mean a fellow sailor at the marina.
03-05-2007 04:14 PM
cbayermd We just had rigging replaced in Sausalito by JP of JP Boatworks. He did a great job and was able to advise us on some other smaller issues that needed attention. He also went out to sail with us after he completed the job to check the tension, etc. We did not have to remove the mast. He sometimes delivers boats up and down the california coast and might come to LA to do the job. At any rate, i am sure he could reccomend someone in the area. Good luck!
03-03-2007 10:45 PM
sailingdog It depends on the design of the rig. You don't always have to lower the mast to replace the rigging. You can often do one piece at a time, and leave the stick up. If you're replacing the backstay or forestay, and only have the one..you can often temporarily support the mast using a halyard or topping lift, tightened to an appropriate spot.
03-03-2007 09:14 PM
bcbirkhauser is it important to get the right tension? I've heard that's the most difficult part. Also how do i get the mast down without a crane or something to support it? I have a 68' bristol 29 sailboat. Is it necessary to bring the mast down to replace the rigging? Thanks for your help.
03-03-2007 08:59 PM
Morgan3820 Take the mast down. get some Sta-loks, wire cutters and a spool of wire. match the stays length. Install the Sta-lok (easy). Should take less than a day.
03-03-2007 08:48 PM
bcbirkhauser
replacing standing rigging

I need to replace my standing rigging. I have heard some people have replaced their own and I'm curious to get people's impressions and advice on the best way to go about doing this... Is it something that I can do myself or should I pay to have someone do it for me? Does anyone know of a good rigger in the los angeles area? Thanks in advance.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 10:07 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.