SailNet Community - Reply to Topic
Thread: Universal Instrument Panel Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
12-08-2013 07:13 AM
H and E
Re: Universal Instrument Panel

I had a similar issue with the fuel gage. I pulled the panel to install a new tach and found a few loose connections. Cleaned and tightened. All is well now.
12-06-2013 01:14 PM
Re: Universal Instrument Panel

Originally Posted by snotter View Post
Trailer connector in the wiring harness leading from the engine to the pannel?
Follow the link in my earlier post. This is how Universal made for a quick connect harness. The problem is that these connectors would oxidize, as current would pass through the increased resistance from the oxidized connector, it would generate heat, and MELT THE CONNECTOR...

This is a serious problem with the old instrument panels that had an Amp meter, because rather than using a shunt, the 51 Amp output from the alternator ran directly to the meter through two of these crappy connectors.
12-06-2013 12:54 PM
Re: Universal Instrument Panel

Trailer connector in the wiring harness leading from the engine to the pannel?
12-06-2013 11:06 AM
Re: Universal Instrument Panel

The problem with the ammeter is, if the charging current from the alternator is passing through it, you tend to lose a lot of charging efficiency. On my Universal 5424, there is a direct wire from the alternator to the battery switch, so the ammeter reads nothing when running as all the charging current is bypassing it.
12-06-2013 10:30 AM
Re: Universal Instrument Panel

Thanks everyone. I will check on these things next visit to the boat.
Honestly I'm not sure what I have/don't have...
12-04-2013 01:44 PM
Re: Universal Instrument Panel

Oh; PLEASE tell me that you do not have an AMP meter in your panel...
12-04-2013 01:39 PM
Re: Universal Instrument Panel

It is likely that you either have a bad ground, or bad connection on the +12VDC side of the gauge.

The FIRST thing that I would do is to verify that the old, "plug-style" connection to the gauges has been retro fitted to the newer, "screw-type". See and this; http://forums.catalina.sailboatowner...d.php?t=135558

If that is OK, then I would take an Ohm meter, and test for continuity to the ground (black [likely], or yellow[less likely]) connection at the rear of the panel, by shaking the wire. If this works, shake the wire at the harness connector, and again near where it ties into the ground for the boat. I'd do the same with the +12V (Red) wire, testing for continuity between the 12V breaker that powers the instruments.
12-04-2013 01:31 PM
Re: Universal Instrument Panel

At least in cars and motorcycles that happens when you have a bad ground.
12-04-2013 01:03 PM
Universal Instrument Panel

I need some advise on why my Instrument Panel is not working properly please. I have a 1999 Universal Diesel Engine (M-25XP) with an instrument panel which was likely installed at the same time.
I've had the boat 6 yrs. and do most maint. myself, with a few projects left to the pros.
This past year my engine appeared to be running very well, but the instrument panel is not working correctly- all of the guages bounce around when at idle and also while in gear.
I've checked all connections at they "appear" to be connected...
Maybe a short in one of the wire connectors?
Any thoughts?
Any direction is greatly appreciated!

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome