SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Rudder/tiller head is loose
 Not a Member? 


Thread: Rudder/tiller head is loose Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
12-19-2013 07:33 PM
Delezynski
Re: Rudder/tiller head is loose

Mrhoneydo,

You might want to view my short YouTube video at;

It shows how I shimmed our rudder in 2007 and it is still working with NO play.

Greg
12-19-2013 07:12 PM
capt jgwinks If you must pull the rudder head off in the water, first c check if theres a clamp or something to keep it from dropping out. Even if there is one out might not take the weight impacting it. You could put a heavy duty hose clamp around the shaft tight against the stuffing box. I keep one on my propeller shaft to keep it from pulling put if the coupling lets go.
12-19-2013 01:21 PM
Captainmeme
Re: Rudder/tiller head is loose

I had a Hunter 25 that has similar slop between the rudder post and rudder tube. I cut up some plastic milk jugs to make shims to take the slop out. After some time (years, how many, I don't remember) there was still no slop.
12-19-2013 01:11 PM
DonScribner
Re: Rudder/tiller head is loose

My tiller does the same. I can't drill a large enough hole to remove the slop without compromising the rudder post. But, I can drill the tiller bracket to accept a reducer bushing, either bronze or Nylon 6.

Don
12-19-2013 12:48 PM
flo617
Re: Rudder/tiller head is loose

I suggest you post this question here:

Yahoo Groups

There are a few C28 owners that are active on this forum and could help you.

Given the fact it is a spade rudder I would be careful and examine the issue when the boat is out of the water and assume the rudder will come down to be on the safe side.

Florent
12-19-2013 12:23 PM
mrhoneydew
Rudder/tiller head is loose

Hello Everybody. I recently acquired a '69 Columbia 28. The tiller has a fair amount of "slop" to it. I get a slight amount of lateral movement in the rudder post (likely loose bearings), which I will address at haulout. I am pretty sure I have figured out that the pin where the tiller attaches to the rudder head is loose. This is because the hole through the rudder head is a little wallowed out when the pin should be a snug fit in there. So my first concern is, if I pull the rudder head off is my rudder going to plummet to the bottom? I am thinking I will drop a couple of lines under the rudder and tie it off. Next question is, can I drill out the hole through both tiller head and rudder head and get a larger pin, or would this compromise the integrity of both so that it could break under load?

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 04:29 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.