|Topic Review (Newest First)|
|04-17-2007 01:17 PM|
Originally Posted by hellosailor
If you look at the alt belt you see the same thing as the hose; cracked paint. It sure makes a mess in the engine compartment.
|04-17-2007 11:36 AM|
Rick, that elbow hose above the alternator looks like it was factory painted--and is now already cracked and ready to replace.
Don't tell me...they hired the alleged engineering team from WesterBleeech ?!
|04-17-2007 08:17 AM|
Originally Posted by arisatx
|04-12-2007 09:50 PM|
I ordered zinc #cmpnzd based on the 1.25" dia prop shaft that this PS32PH uses. I'm also missing the bolt that holds the anode to the prop nut and it appears to be a 5/16 x 18? We are in fresh water and not nearly the concern like the saltys have, but it will protect the brass prop from electrolitic corrosion. I took off the godgeon today and have the rudder supported by a floor jack. I'm going to wire wheel all of the undercoating off of it from the po, grease it up and reinstall it. After taking a mirror and looking up the rudder tube I see a cement type bedding inside of the pipe but it doesn't fill it up from side to side. I have no idea why that would be in there and as far as I can tell looks like it has something to do with the rudder sticking to it and not with sealing off the tube from water, which it wouldn't be able to do the way that it is. That tube has got to be drilled in numerous spots with some sort of a steel reinforcement going into the rudder and perpendicular to the tube, right? The rudder pipe or tube sticks about 1.125" out of the bottom of the rudder and the receiving gudgeon brass bushing is approx 1.375 deep. Both the pipe inside of the rudder and the bushing have seats that are the main contact point. No wear noticed after polishing and of the surfaces. The bushing in the gudgeon has about a .25" hole in the bottom of it, a little small for zebra musscels, I hope. Next year I'm going to shove grease into that bushing hole and call it good. It appears that the gudgeon, bolts and nuts were well sealed from water and I plan to reseal them at least as good.
|04-11-2007 11:19 PM|
|arisatx||Thanks Rick - will take a look at West's catalog when I get home.|
|04-11-2007 05:38 PM|
Originally Posted by arisatx
I found the anode. It's on page 360 of the west marine 2007 catalog. We don't have the same prop, yours has gears, is adjustable and feathers? Mine just drags along for the ride.
|04-03-2007 08:18 PM|
Included in the kit,
1. Marine XM Weather Antenna/w/50 feet of cable.
2. Base unit
3. Mounting bracket for the base unit
4. Auto XM antenna with magnetic base.
5. USB cable for laptop connection
6. 12 volt power adaptor
8. Delphi XM radio receiver
8. free activation for XM Weather and Radio
9. free first month for XM Weather and Radio
10. free annual deactivation, free activation next year
|04-03-2007 01:05 PM|
|hellosailor||They charge that much for it?! What, is $500 for the software side?|
|04-03-2007 08:17 AM|
Thanks for the information and your insight. I try to be careful with technology and those greedy corporation pundits, not wanting to own a $600.00 doorstop if XM and its WxWorx were to be put down.
|04-02-2007 11:22 PM|
Rick, the merger is still on the table. The problem is that it would be illegal under the terms of their FCC licenses, so you can expect that it will need a special sanction by the FCC, plus possibly approval from the SEC (because of monopoly issues) and the FTC (again).
Those kind of merger approvals usually take 6-12 months and you can't get a bookie to take odds on whether any of the agencies will approve it. Odds are the FCC will approve it, simply because they could arrange to "take back" one of the frequency allocations and sell it off again, and the FCC is very busy selling allocations to help pretend the federal budget is balanced.
|This thread has more than 10 replies. Click here to review the whole thread.|