SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Electricity (European to American)
 Not a Member? 


Thread: Electricity (European to American) Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
04-22-2007 07:19 PM
ebs001 Before re-wiring check the guage of the wire to the various a/c items. You will probably find that it is minimum #12 AWG equivelant. You will want to replace any receptacles with 120v/15a NA ones. The battery charger and hot watertank (OR at least the element) will have to be replaced if you want to convert the boat to NA standard which to me makes more sense than mixing systems.
04-22-2007 05:27 PM
Idiens If you are not running an emmersion heater or something else with a high Watt load, the wiring will be OK. In any case, its only the wire running up to the transformer that takes the 110V 2x Amps load. Beyond it, the voltage is 220 V and current normal for a 220V wired boat.
Most things will be running on the DC circuits, which are the things that are intended to run offshore, so its only the direct AC loads are a worry. Check the battery charger is not worried by 60 Hz. If the boat can drive its 220V installations through an inverter from the batteries, then the charger may be the only item sensitive to 60Hz.
04-22-2007 05:09 PM
sailingdog If you have a boat setup for Europeann 230VAC 50 Hz... and wanted to set it up for 110VAC, you will probably need to re-wire it completely on the AC side because the wiring will generally be too small to handle the same power loads at the lower voltage, since the amperage will double. 1500 Watts at 220V is 7 Amps, at 110V it is 14 Amps.

A isolation transformer is probably your best bet.

The frequency isn't too much of an issue, as many electrical motors and such can run over a range of frequencies... 50-60 Hz in general. You should check the equipment labels, most will state what frequency range the equipment will work over.
04-22-2007 02:35 PM
coldandhardy
Electricity (European to American)

I have found a couple of Privilege cats that I am planning to travel to see. One is set up with standard North American power 110V 60 hz and the other one is set up with 230-240V / 50 hz. I have read articles about Eurpean power conversion considerations for N.A. boats visiting European waters but I have not seen anything regarding the opposite.

The European boat that interests me has lots of electronics, and electrical stuff and it is likely that the wiring and fuses are all designed for 230 Volts. A partial option would seem to be to install an isolation transformer to boost N.A. power up to the 230 volts (the isolation transformer would also protect against galvanic corrosion from shore power I have read).

This seems to me to only be a partial fix because the 50 hz vs. 60 hz would still be a problem for anything with a motor in it particularly. I am not aware that hz is changed in such transformers as well as the voltage but I assume would rather require a more complicated electric motor/generator system I believe to run ship systems like an air conditioner, fridge & freezer while hooked up to land.

Does anyone have suggestions or referrals to articles that have been written on this subject from others experiences?

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 01:03 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.