SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  

Quick Menu
Boat Reviews  
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Hatches and Portlights
Interior And Galley
Marine Electronics
Other Items
Plumbing and Pumps
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here

Go Back   SailNet Community > On Board > Gear & Maintenance > shroud clamp..
 Not a Member? 

Thread: shroud clamp.. Reply to Thread

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

Topic Review (Newest First)
05-24-2007 01:24 PM
TrueBlue Shaft collars, spreaders, worn fingers, beatings . . . sounds kinky.
05-24-2007 01:13 PM
hellosailor No beating?! But I was SO looking forward to the beating.

Worn aluminum fingers, huh. Who knew spreaders even had fingers.
05-24-2007 01:02 PM
groundhog Very perceptive grasshopper!

You are correct. No beating for you today!

At the base of the spreaders where it attaches. This is called the hound or something. Well, this part is made of cast aluminum and has little fingers that are supposed to prevent the spreaders from moving in one direction (down I think). Kind of the same as your cell phone, where it opens to a point and then the little hinge stops hit. On mine, the little aluminum fingers are worn, so the spreader can move too far down.

So my clamps are just fixes to a problem that may not exist on other boats of this type.

05-24-2007 12:45 PM
hellosailor groundhog, I'm just wondering--

Is this a problem unique to your Vega, indicating something else is wrong?

Or a part that others have, which went stray from yours?

Or a problem endemic to all Vegas?

Maybe there's something else that is wrong, which is causing this problem, which in turn needs fixing? Something other Vega owners might be able to give you a hint on?
05-24-2007 12:25 PM
groundhog I have an albin vega 27.

Here is what I plan to do for the record..

My spreaders have hinges at the mast so they can move up and down a bit.
Currently I have a spreader roller on the shroud to protect the foresail when it hits the spreader. The spreader roller comes with two disks, one large one that rolls, and one small one that clamps tight to the shroud wire.

I couldn't find another small clamp when searching the marine type parts.

But, these small disk shaped clamps are also known as "shaft collars".
Looked on McMaster Carr and found a nylon one (they also have steel and aluminum) that comes in two pieces with screws to tighten it.

So that's my plan. Still have to install them.

05-20-2007 07:35 AM
sailingdog It would help if you said what kind of boat it was, as well as posted a photo of the problem.

My boat has clamps built into the spreader ends to secure the spreader tip on the shroud. Basically, it is a piece of metal with a screw through it... tighten down on the screw... clamps the shroud in place. You could probably do something similar with your spreader tips.
05-19-2007 11:46 PM
Sailormann What kind of boat do you have ? Do you have more than one set of spreaders ?
05-19-2007 08:56 PM
shroud clamp..

I have a problem with my hinged spreaders sliding down my shrouds.

Above the spreader on the shroud wire, there is a small disk clamp that prevents upward movement.

I would like to buy another one to put below the spreader end but I am having a heck of a time finding any reference on the internet about this type of thing.

Does anyone know what I am talking about and know who sells such a thing?

Or is there a better way to solve this problem?


Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

All times are GMT -4. The time now is 05:43 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) LLC 2000-2012

The store is owned and operated by a company independent of the forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.