SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Question on Dipstick for Clutch on Yanmar 2GM
 Not a Member? 


Thread: Question on Dipstick for Clutch on Yanmar 2GM Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
05-29-2007 09:03 AM
jrpla Hi, PB

I have the same problem 1 year ago, you need to change the oil, do several changes the same day to make sure you take out all the old oil.

One you change it, the problem is fixed, if not then you need to call a mecanic to inspect your transmission.
05-25-2007 10:22 PM
PBzeer Adding oil, did seem to make a difference. Not a big one, but noticeable.
05-25-2007 08:56 PM
billangiep PB,
The Yanmar dealer here in St. Pete recommends non detergent straight 30wt. There is not a clutch per say but what is called a "cone" nine times out of ten if your tranny is slipping that is the problem. Have you checked your shift linkage? It is very critical that the linkage maintains pressure on the shift lever of the trans. There is a barrel type piece (can't remember what it's called) that is attached to the end of the shift cable then to the shift lever itself on the trans. This has a double acting spring to keep tension on the shift lever both in forward and reverse. Hope this all makes sense?
Bill
05-24-2007 12:03 PM
jrpla Hi,

I have same motor on a beneteau 32.

to read the oil start the engine a few minutes, turn off, unscrew the dipstick, clean it and then put it to read it without screw in it.

Is very dificult to see the oil in the stick, use a white paper, then touch the paper with the stick to read it.

A few month ago my clutch was sliping, you need to change the oil with new HD 30 oil, it use so little, you need to fill it little by little and messure it.

Don't overflow it because it will hot the transmision.
05-24-2007 11:25 AM
PBzeer Yes, that's the correct way to read it, just wasn't sure about the mark. On a related note, would low oil cause the clutch to slip?
05-24-2007 11:22 AM
SailorMitch PBZ -- Yes, you are reading it correctly. Working from memory here, but I think when putting the dipstick back in for the reading itself (after cleaning the residual oil off) you don't screw it in, just let it hit the top of the opening and take the reading from that. I'll look at my servive manual tonight, but I'm pretty sure that's the recommended way to do it.
05-24-2007 10:59 AM
PBzeer
Question on Dipstick for Clutch on Yanmar 2GM

Pulled the dipstick for the Clutch oil, but I'm not sure how to read it. There is one black ring, about a 1/2" up from the bottom, that I assume is the full level. As the clutch is obviously low (barely on the dipstick) and doesn't take much oil, I want to be sure I'm reading it correctly.

Thanks,

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 07:58 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.