SailNet Community - Reply to Topic
Thread: 1983 Newport 27S-II Hull construction and Sonar Transducer Installation Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
10-06-2007 03:38 PM
Solid vs. Cored hulls; New sonar revelations !

Thanks Chicago,

Although that brochure does muddy the waters with that statement about "hand lay-up foam core and fiberglass method," I did actually find an original section of hull about 6x8" stashed away in a storage compartment, that seemed to be some sort of "message in a bottle" from Capital Yachts....marked with the original Hull number, what the engine was, and it was spelled "Unibersal" instead of "Universal," seemingly written by a possible spanish-speaking Capital Yachts laborer doing the hull, and that section was solid fiberglass.

However, I ended up side-stepping the whole issue of whether I had a cored hull or not.

It turned out I was able to use my old depth sounder transducer to feed to my new Lowrance LMS-525c (I got that instead of the Eagle, because the LMS has NMEA2000 networking capability and the Eagle doesn't), and it works perfectly!

Either a previous owner, or maybe Capital Yachts, had installed a Moor digital depth sounder with a single-frequency (200Khz) through-hull transducer in my 83 Newport 27-S MKII..

When the depth sounder went dead 6 months ago, just blinking random numbers, I contacted Moor to have it repaired. They had me ship it and the transducer (which is REMOVABLE WHILE IN THE WATER, thanks to a dummy/service plug !!!) up to them in NY, where they reported back the head unit was fine, the transducer had died. I told them I was thinking of buying a new graphic unit anyway, like the Lowrance or Eagle, and asked whether I could use their transducer (If I bought a replacement) and feed it to both their unit, and a new Lowrance. They didn't know, but referred me to the actual manufacturer of the transducer, Radarsonics.

RadarSonic's head engineeer Max said "sure, no problem, but you can't send to both units at the same time, I'd have to put together a switchbox for you." So he did, and I got a new dual-frequency transducer from them to feed the LMS-525c and old Moor unit (the Moor doesn't mind, it just ignores the 2nd frequency), installed it all, and it's using the original Moor through-hull mounting, and it all works perfectly....I can switch back and forth between the Moor and the Lowrance and they are within .1 digits of each other in accuracy. Max, who has been designing and building transducers for 30 years, tells me "...there is no need for any calibration of the transducer signal between units....they just work"....and they do!

The only limitation is the Moor does not like being switched "hot," you need to switch the transducer feed to the Moor before the Moor is powered up, but other than that, it all works perfectly....and I now have GPS charting on top of dual depth sounders, thanks to the Lowrance unit.

Custom Switch box and dual-Freq transducer total: ~$180 !!

06-22-2007 11:35 AM
ChicagoNewport27 Check the capital yachts website, but I believe it is solid with a few areas of foam core.

The brochure says:
"The Newport 27-S is built by the hand lay-up foam core and fiberglass method."

Newport 27 Bochure

I've installed a couple thru-hulls in my 1976 Newport 27 (granted, not a 27-S), and the plugs that came out didn't have any wood coring material.

I'm sure the construction varied from year to year, but I would be surprised if they suddenly decided to start coring their hulls with balsa.
06-22-2007 12:56 AM
1983 Newport 27S-II Hull construction and Sonar Transducer Installation

I've asked this over in the Newport 30 Hull thread, but I'll ask it here too, to get a little more visibility....

Anybody know how Newport's/Capital's hull construction varied with year and model? I have an 83 Newport 27S-II that I'd like to install an Eagle Seacharter 640C Sonar/GPS in, and do the easy Shoot-thru-Hull transducer installation, IF I have a solid hull......but if it's cored, I am not going to cut through the balsa from the inside until I get to the outer thanks.


Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

For the best viewing experience please update your browser to Google Chrome