SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Need material to raise floor of bilge slightly
 Not a Member? 


Thread: Need material to raise floor of bilge slightly Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
09-20-2007 08:30 PM
sailingdog If you do as Frank suggests, use either MAS Epoxy or don't let it cure completely, and add the additional layers while the previous ones are still tacky to the touch or you'll have to wait for it to cure and remove the amine blush. If you don't remove the amine blush, the layers won't bond to each other very well. MAS epoxies are formulated not to have an amine blush IIRC.
09-20-2007 06:54 PM
Valiente Seeing as it's straight fill, you can make the first layers with chopped mat and/or microballoons. You could finish by wetting out fg tape and overlapping it up the sides of the bilge, which should keep water from ever getting beneath it

If this is a concern, however, or if you have no boat cover or you haul in a place where water is likely to freeze, consider boring a "garboard drain" to the outside with a close-fitting plug. Remove the plug in the fall and water drains straight out.
09-20-2007 06:37 PM
FrankLanger I had a small section at the bottom of an anchor locker that was below the drain hole, and was successful in simply pouring some mixed epoxy in until it got to the desired level. The only caution is that epoxy creates heat as it cures, so don't put in too much at once--the heat could cause problems for other things in the vicinity, or could cause the new stuff you pour in to crack as it cures. I would suggest doing it in layers, perhaps about a 1/4" at a time, let that cure and then mix and pour more until you reach the desired level.
Although it worked fine for me, I'm no expert on this, so it's only a suggestion for consideration.
Frank.
09-20-2007 04:03 PM
svindigo Could you just expand the limber holes to reach the bottom of the existing compartments? Then no worries about adhesion or trapped moisture under the filler.

Just a thought
09-20-2007 03:06 PM
Faster If you're not looking for strength, and just basically trying to fill a space, there are two-part rubber compounds (similar to "Spartite") - Devcon is one maker of such material. You mix two parts into a syrupy rubber soup that pours into place and self levels and then sets..

Make sure the area to be filled is as clean as possible for good adhesion.

Getting it out later if necessary would be a chore, so be sure this is something you want to be "permanent".
09-20-2007 02:55 PM
saltypat
Need material to raise floor of bilge slightly

The bilge has, coming from the mast aft, 3 shallow compartments (about 9 inches deep, 18 " by 12",and then a deep compartment which ends well before the companionway, 3-4 ft. deep.

The two compartments closest to the mast do not drain completely as the limber hole pipe is slightly too high - I would like to raise the level to the limber hole with some TBD material.

Sailingdog suggested "a marine epoxy putty like, MarineTex, which will cure even if it gets wet. However, it does need a temperature of 70˚F or so to do so, so some heat may be required. If you decide to use MarineTex, get it as fair as possible, since it is very tough to sand fair once it cures."

Where I need to put this stuff has a support beam overtop which makes access difficult. It would be nice if I could use a material that pours rather than needs to be spread.

Any suggestions out there? I am imagine I might look for something in a craft shop, etc. The material doesn't need to provide strength as ,nothing is broken.....

Thanks! Saltypat

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 08:38 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.