|Topic Review (Newest First)|
|11-04-2007 10:03 PM|
I just looked on the boat, with all your advice in mind, and decided I will leave things the way they are for now. Taking off the boom seems inevitable and I do not think the condition of the lines warrant this task.
I can't believe they would make it so difficult for such a simple thing...
I took some pictures of both ends, and the sliding eye that I'm still curious as to its purpose.
They are in my gallery, I still can't post a link.
Sailormann -"Make sure that you don't have your boom upside down as there are tracks on the top and on the bottom of the Isomat boom, and the movable eyes that you are describing usually run along the bottom track..."
The way the sheaves on the aft end are set up it appears to be right...??
Thank you, all have been extremely helpful .
|11-04-2007 01:35 AM|
Re-reeve is just a nautical way of saying you're replacing a line.
Might want to read this page about why you really should use a two-line reefing system, rather than a single-line reefing system.
|11-03-2007 09:12 PM|
Originally Posted by sailingfool View Post
|11-03-2007 08:44 PM|
Originally Posted by Northeaster View Post
I would not open up the boom to mess with your outhaul unless your boat has been subject to a lot of wear-and-tear and you have run out of other things to fix.
|11-03-2007 08:21 PM|
On a 34 foot Hunter I'd expect at least a 4 part - hopefully a 6 part purchase inside the boom (similar to the mainsheet but smaller line). The aft end of the tackle will be shackled to the wire that comes out the boom end sheave and attaches to your mainsail clew.
You can check how many parts it is by seeing how much line you need to pull to get, say, an inch (2.5 cm) of outhaul travel. If it takes 6 inches of pull to get 1 inch, you have a 6:1 tackle.
By re-reeving I meant you need to run your new line properly through both blocks inside the boom. Since the bitter end of the tackle is on one of the blocks inside you'll have to get at that. This will require removing the rivets and pulling the boom off the end cap.
Rivets can be replaced with the proper tool and appropriate "pop" rivet style fittings. Make sure they are aluminum or stainless steel and of adequate size and strength. Alternately you may be able to thread the holes in the end cap casting and use machine screws.
This is certainly something you can do yourself, and yes, sinking the boat is not something you need to worry about (at least for that project!
|11-03-2007 07:42 PM|
Originally Posted by Faster View Post
The boat is a 34ft Hunter .
If I understand this right the wire is attached to a block inside the boom, said block has one end of the rope tied to it then trhu pulley sys and out to goose neck ?
If I drill out the rivets what type of rivets need to be used to resecure ?
or should this be left to professionals.... not that there are any available around here... So can a rookie like myself be able to do this?
At least it will not sink the boat if I screw it up.... RIGHT ?
Thank you again to all of you who have contributed to enlighten me.
OK so I'm slow .. I just do not like to dive into something with little information and make things worse.
|11-03-2007 05:51 PM|
|Faster||Northeaster - most use tack hooks at the gooseneck for the tack while reefing. But you could use a similar system to a cunningham to rig up cockpit-led tack reef lines.|
|11-03-2007 03:57 PM|
Sailormann- Just curious. In your diagram of the boom / reef line, they don't show any tack reefing lines - just the 1st and 2nd reef lines for the clew. What would be the typicla setup for the tack?
My 30' boat has no lines inside the boom, but I would like to see how this is set up.
|11-03-2007 12:55 AM|
Originally Posted by MiVelero View Post
|11-03-2007 12:34 AM|
Originally Posted by pegasus1457 View Post
|This thread has more than 10 replies. Click here to review the whole thread.|