SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > slight bulge in side of boat
 Not a Member? 


Thread: slight bulge in side of boat Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
11-29-2002 03:13 AM
soverel28
slight bulge in side of boat

I wonder if it might be that it is the
result if stays being too tight for a
length of time?
But I guess that would be an indention
not a bulge.
PaulB
11-28-2002 02:40 PM
Jeff_H
slight bulge in side of boat

While it is unlikely that it has always been there, the bulge probably appeared in the first few years of your boat''s life. Pearson during that era tended to use a lot of acellerators in their resin and allow a comparatively short cure time. Tritons, also had a minimum of internal framing. Allof this would promote a tendancy toward the hardspot to be especially pronounced compared to later, and better built boats.

Whether you should be concerned with this or not depends on how you plan to use your boat. These hardspots tend to be more fatigue prone than other areas of topsides. Given the more brittle resins and laminates of the era, this typically would be an area of decreased strength over other portions of the topsides. Used normally this weakening should be of no problem, but exposed to the kind of thrashing involved in major long distance passage making eventually this could prove to be a problem.

As the prior poster noted, the bigger problem is the condition of the bulkead and tabbing. Pearsns of this era had structural bulkheads and they were often covered with Formica, which both can foster and can mask ongoing rot problems.

Jeff
11-27-2002 07:26 PM
jparker11
slight bulge in side of boat

My guess is you have developed a supercritical eye. I had an occasion a number of years ago to investigate some tabbing on a bulkhead on my Ranger 26. Although there was no damage, I learned to "see" bulkheads on everyone else''s boat!!!

What you have is a hull laminate that is laid up and cured. Typically, laminates will creep or shrink about 2% while curing. A few weeks later, the bulkeads are tabbed into place. They adhere to the cured hull laminate and undergo there own creep (or try). The resulting "pull" induces some stress in the hull laminate. Over time the stress elastically relieves itself, not before a minute deflection is created, just enough to bend the light while sighting down the hull. Cored laminates, Tritons hull laminates pre-date these, make this less visible from the exterior. (Read about Larry Ellison''s sled in the Syd-Hobart race pulling the tabs right off of the inner laminate!!!)

Things to watch in the hull at bulkheads are punching shear action created by slamming in to a wharf finger or glancing collisions. These will show up as star fractures in the gelcoat.

Of more concern on a boat of that vintage is the integrity of the bulkhead materal.

Now go see if you find the other bulkheads on the Triton or you neighbor''s boat. Bet you can.

11-27-2002 06:51 PM
SailorMitch
slight bulge in side of boat

Finding a "hard" spot in the hull is not all that unusual. But go to this site and ask your question there for the experience of other Triton owners: http://www.tritonclass.org
11-27-2002 12:15 PM
bantrybayboston
slight bulge in side of boat

I have noticed a slight bulge on the outside of the hull of by boat (64'' Triton). It is only a slight bulge, running vertically. It seems to match up to where the bulkhead is tabbed to the inside of the boat. The previous owner assured me it had "allways been there", but now I''m starting to wonder. Is this a problem or could it have allways been there?

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 02:10 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.